Mitsubishi Lancer Evolution 7. Manual — part 342
BODY -
Doors
42-29
B
Note
Section A-A
View A
View B
Claws positions
Clips positions
<REAR DOOR>
Rear door trim
View A
View B
Door panel
Door trim
Clip
D
Cap
View C
D
Section C-C
Cap
Claw
Pull handle box
View C
B
AW0461AU
AW0772AQ
BW0465AU
Section D-D
Section B-B
Door trim
Clip
C
C
C
C
C
C
A
A
C
C
B
B
Power window switch
panel assembly
Power window switch
panel assembly
Claw
Door trim
Power window switch panel assembly
AW0465AU
BODY -
Doors
42-30
REMOVAL SERVICE POINTS
A
A" DOOR INSIDE HANDLE COVER REMOVAL
1. Insert the driver into the tapping screw cap end of the
door inside handle cover and pry the cap the way shown
in the illustration to remove the cap, and then unscrew
the tapping screw.
2. As shown in the illustration, insert the special tool between
the door inside handle cover and door inside handle,
and then disengage the claws of the door inside handle
cover and door inside handle.
3. Insert the special tool into the door inside handle cover
end, and then pry and remove the door inside handle
cover.
A
B" CLIP REMOVAL
Use a cloth to remove the clip as shown in the illustration.
Tapping screw cap
MB990784
Door inside handle cover
A
A
B
B
Door inside
handle cover
Door inside
handle cover
Claw
Claw
Claw
Door trim
Section A - A
Section B - B
Door inside
handle cover
Special tool
insertion
position
BODY -
Doors
42-31
INSTALLATION SERVICE POINTS
"
AA WATERPROOF FILM INSTALLATION
Apply the specified adhesive on the waterproof film as shown
in the illustration, and then glue it on the door window glass.
Specified sealant: 3M ATD Part No. 8625 or equivalent
"
BA REGULATOR HANDLE/ESCUTCHEON/CLIP
INSTALLATION
1. Install the clip and escutcheon to the regulator handle.
2. Close the front door window glass fully, and then install
the regulator handle as shown in the illustration.
INSPECTION
Power window main switch uses SWS system, for the
power window main switch check, refer to GROUP 54B
- SWS.
POWER WINDOW SUB SWITCH CONTINUITY CHECK
Switch position
Terminal No.
p
2
3
6
UP
DOWN
Waterproof film
<REAR DOOR>
<FRONT DOOR>
Waterproof film
Front of vehicle
30_
Horizontal line
BODY -
Doors
42-32
DOOR GLASS AND REGULATOR
REMOVAL AND INSTALLATION
Pre-removal Operation
Door Trim and Waterproof Film Removal (Refer to
P.42-27.)
Post-installation Operation
D
Door Window Glass Adjustment (Refer to P.42-21.)
D
Door Trim and Waterproof Film Installation (Refer
to P.42-27)
1
2
3
1
<REAR DOOR>
<FRONT DOOR>
3
4
2
5
6
1
1
<Vehicles with power windows>
<Vehicles without
power windows>
<Vehicles with power windows>
<Vehicles without
power windows>
Window regulator assembly
removal steps
"
BA D Operation check <Vehicles with
power window>
A
A" "AA 1. Window regulator assembly
A
A" "AA 2. Power window motor assembly
Window glass removal steps
D
. Window glass runchannel (Refer to
P.42-39, 40.)
3. Door window glass
Stationary window glass removal
steps
D
Window glass runchannel (Refer to
P.42-38, 39.)
D
Door window glass lower runchan-
nel (Refer to P.42-38, 39.)
3. Door window glass
A
B"
4. Door center sash
5. Stationary window glass
6. Stationary window weatherstrip
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст