Mitsubishi Lancer Evolution 7. Manual — part 348
EXTERIOR -
Side Air Dam, Molding and Garnish
51-9
SIDE AIR DAM, MOLDING AND GARNISH
REMOVAL AND INSTALLATION
1
1
Clip
Clip
Clip
1
Section A – A
Section B – B
Section C – C
Section F – F
Clip
2,3
1
Clip
Section D – D
1
2
3
1
Clip
Section E – E
NOTE: Refer to P.51-14 for more information regarding removal and
installation of front deck garnish.
F
F
A
A
B
B
C
C
D
D
E
E
F
F
B
B
B
B
A
A
<Gray>
<Milky white>
<Blue>
<Purple>
<Orange>
<Blue>
<Yellow>
Double-sided tape: Generic products: 5mm width, 1.2mm thickness
3
A
A"
1. Roof drip molding
2. Delta outer garnish
A
B" "AA 3. Side air dam
EXTERIOR -
Side Air Dam, Molding and Garnish
51-10
REMOVAL SERVICE POINTS
A
A" ROOF DRIP MOLDING REMOVAL
Use the special tool to pry the molding from the rear of the
body for removal.
Caution
Do not use the deformed mold again.
A
B" SIDE AIR DAM REMOVAL
1. Attach protection tape all the way along the edges of
the double-sided tape which is still adhering to the body.
2. Use a resin spatula to scrape off the double-sided tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag moistened
with isopropyl alcohol.
INSTALLATION SERVICE POINTS
"
AA SIDE AIR DAM INSTALLATION
Double-sided tape affixing to the side air dam (when
reusing)
1. Scrape off the double-sided tape with a resin spatula
or gasket scraper.
2. Wipe off the side air dam adhesion surface and clean
it with a shop towel moistened with isopropyl alcohol.
3. Affix the specified double sided tape to the side air dam.
(Refer to P.51-9.)
MB990449
Protection tape
Double-sided tape
EXTERIOR -
Side Air Dam, Molding and Garnish
51-11
4. Remove strip paper from the pressure sensitive
double-sided tape.
NOTE
Affix double-sided tape to the end of strip paper for ease
of strip paper removal. (Refer to P.51-9.)
5. Install the side air dam.
NOTE
If it is hard to affix the double-sided tape in winter, heat
the application surfaces at both the vehicle body and
the side air dam.
Body 40 - 60 _C
Side air dam 20 - 30 _C
Apply pressure fully to the side air dam.
Adhesive tape
Backing paper
EXTERIOR -
Rear Spoiler
51-12
REAR SPOILER
ADHESIVE
Application
Brand
Rear spoiler
Double-sided tape [15 mm width 1.2 mm thickness, 30 mm width 1.2 mm
thickness]
REAR SPOILER
REMOVAL AND INSTALLATION
1
1
2
3
2
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
5.2 ± 0.2 N·m
A
A
B B
Steel plate hook
2
Claw
2
3
3
3
Double-sided tape:
Generic products: A : 15mm width, 1.2mm thickness,
B : 30mm width, 1.2mm thickness
Section A – A
Section B – B
A
B
Removal steps
D
Trunk lid bumper
(Refer to Group 42.)
1. Gasket
2. Cap
A
A" "AA 3. Rear spoiler
NOTE:
The removal and installation service points are the
same as SIDE AIR DAM , MOLDING AND GARNISH.
(Refer to P.51-10)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст