Mitsubishi Lancer Evolution 7. Manual — part 349
EXTERIOR -
Windshield Wiper and Washer
51-13
WINDSHIELD WIPER AND WASHER
SERVICE SPECIFICATIONS
Item
Standard value
Stop position of the windshield wiper arm/blade assembly (distance between the edge of
34
±
5
Stop position of the windshield wiper arm/blade assembly (distance between the edge of
the wiper blade and the end of the deck garnish) mm
34
±
5
TROUBLESHOOTING
The windshield wiper-washer is controlled by the smart wiring system (SWS). Refer to Group 54B for
troubleshooting.
NOTE
If ETACS-ECU is faulty, the windshield wiper can be operable in LO mode only as the fail-safe function.
(Normally the windshield wiper is operable when the ignition switch is turned to the ACC position. When
the fail-safe function is enabled, it is operable only when the ignition switch is turned to the ON position.)
ON-VEHICLE SERVICE
WINDSHIELD INTERMITTENT WIPER
INSPECTIONS
(1) Check the change in the intermittent time of the wiper
operation by using the windshield intermittent wiper
volume.
(2) Carry out troubleshooting if any of them is faulty.
(Refer to Group 54B.)
EXTERIOR -
Windshield Wiper and Washer
51-14
WINDSHIELD WIPER AND WASHER
REMOVAL AND INSTALLATION
NOTE
indicates the clip A location.
indicates the clip B location.
Section A - A
Section B - B
View A
3 ,4
Clip A
13 ± 2 NSm
A
5
4
8.9 ± 1.9 NSm
1
3
Clip B
3, 4
7.4 ± 1.4 NSm
6
4
3
A
A
B
B
2
Windshield wiper motor assembly
and link assembly removal steps
"
AA 1. Wiper arm/blade assembly
2. Hood weather strip
3. Front deck garnish (driver’s side)
4. Front deck garnish (passenger’s side)
A
A"
5. Windshield wiper motor assembly
6. Link assembly
EXTERIOR -
Windshield Wiper and Washer
51-15
5.0 ± 1.0 NSm
4
1
3
2
NOTE: Refer to P.51-19 for more information regarding removal and installation of rear washer nozzle.
5
Washer hose removal steps
D
Splash shild <Right side> (Refer to
GROUP 42 – Fender.)
D
Cowl side trim, front scuff plate, center
pillar trim, lower, rear scuff plate (Refer
to GROUP 52A – Trim.)
D
Rear
seat
(Refer
to
GROUP
52A – Seat.)
1. Washer hose
Windshield washer nozzle removal
steps
D
Connection of washer hose
2. Windshield washer nozzle
Washer tank and windshield washer
motor assembly removal steps
D
Rear end trim, trunk side trim (Refer
to GROUP 52A – Trim.)
D
Connection of front washer hose
3. Washer tank assembly
4. Washer tank bracket
5. Washer motor
NOTE: Refer to GROUP 54A– Column Switch for
removal and installation of wiper washer switch.
EXTERIOR -
Windshield Wiper and Washer
51-16
REMOVAL SERVICE POINT
A
A" WINDSHIELD WIPER MOTOR ASSEMBLY
REMOVAL
1. Remove the windshield wiper motor assembly mounting
bolt.
2. Use the flat-tipped screw driver to disengage the link
between the windshield wiper motor assembly and the
link assembly to remove the windshield wiper motor
assembly.
Caution
Be careful not to damage the windshield glass when
the windshield wiper motor assembly is removed.
INSTALLATION SERVICE POINT
"
AA WIPER ARM/BLADE ASSEMBLY INSTALLATION
Assemble the parts so that the edge of the wiper blade can
stop in the specified position (standard value).
Standard value:(A) 34 ± 5 mm
Windshield wiper
motor assembly
Flat-tipped screw driver
Link assembly
connection
Front deck garnish terminal
A
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст