Mitsubishi Lancer Evolution 7. Manual — part 345
BODY -
Trunk lid
42-41
TRUNK LID
REMOVAL AND INSTALLATION
2
3
4
5
6
7
8
9
10
1
11
12
A
A
B
B
5
5
9
9
14
Measure of
length mm
15
4
9
12
8.9 ± 1.9 N·m
Section A-A
Section B-B
Trunk lid weatherstrip removal
steps
D
Rear end trim <RS-Ⅱ> (Refer to
GROUP 52A.)
"
BA 1. Trunk lid weatherstrip
Trunk lid release cable and trunk
lid release handle removal steps
D
Trunk rear side trim (Left side)
(Refer to GROUP 52A.)
D
Rear seat (Refer to GROUP 52A.)
D
Center pillar lower trim (Refer to
GROUP 52A.)
D
Cowl side trim
D
Accelerator pedal stopper
2. Trunk lid release handle
3. Trunk lid release cable
Trunk lid striker removal steps
D
Rear end trim <RS-Ⅱ> (Refer to
GROUP 52A.)
4. Trunk lid striker
Trunk lid panel removal steps
5. Trunk lid bumper
6. Trunk lid lock cylinder
7. Trunk lid latch assembly
8. Trunk lid hinge mounting bolt
9. Trunk lid panel assembly
Trunk lid latch assembly removal
7. Trunk lid latch assembly
Trunk lid hinge removal steps
D
Rear shelf trim
D
Rear seat (Refer to GROUP 52A.)
9. Trunk lid panel assembly
A
A" "AA 10. Trunk lid torsion bar (Right side)
A
A" "AA 11. Trunk lid torsion bar (Left side)
12. Trunk lid hinge
BODY -
Trunk lid
42-42
Grease application area
6
7
2
REMOVAL SERVICE POINT
A
A" TRUNK LID TORSION BAR REMOVAL
Insert the tire lever into the torsion bar, and then pull upward
the tire lever to remove the torsion bar as shown in the
illustration.
NOTE
As the left and right trunk lid torsion bars are crossed at
the center, first remove the front trunk lid torsion bar at
the center.
INSTALLATION SERVICE POINTS
"
AA TRUNK LID TORSION BAR INSTALLATION
Install the trunk lid torsion bar by the following procedure.
1. Ensure that there is the identification color at the center
of the trunk lid torsion bar.
Trunk lid torsion bar
Identification color
Left side
-
Right side
Red
Caution
As the trunk lid torsion bar (Right side) is painted
with differentiation color in the middle to differentiate
between RH and LH, be careful when installing.
2. Install the trunk lid torsion bar (Left side) as follows.
(1) For terminal A, insert the trunk lid hinge (Left side)
into the fixed hole B
(2) For terminal C, touch the trunk lid hinge (Right side)
against portion E.
(3) For terminal D, insert the trunk lid hinge (Right side)
into portion F until portion G while twisting with the
tool such as a tire lever, etc.
(4) For terminal C, set the trunk lid hinge (Right side)
at portion H while twisting with the tool such as a
tire lever etc.
3. Install the trunk lid torsion bar (Right side) in the same
way as above.
Trunk lid torsion bar
Tire lever
Tire lever
D
Trunk lid torsion
bar
H
Identification
color
Trunk lid torsion bar
(Right side)
Trunk lid torsion bar
(Left side)
Trunk lid hinge (Left side)
A
B
C
D
Trunk lid hinge
(Right side)
C
F
G
E
Trunk lid torsion bar (Left side)
BODY -
Trunk Lid
42-43
"
BA TRUNK LID WEATHERSTRIP INSTALLATION
aligning the trunk lid weatherstrip marking section at the body
center to install.
INSPECTION
TRUNK LID LATCH SWITCH CONTINUITY CHECK
Switch position
Terminal No.
p
1
Earth
Latch open
Latch closed
Marking
section
Joint
section
Trunk lid latch
assembly
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст