Mitsubishi Lancer Evolution 7. Manual — part 325
PARKING BRAKES -
On-Vehicle Service
36-3
ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE CHECK
AND ADJUSTMENT
1. Pull the parking brake lever with a force of approx. 200
N and count the number of notches.
Standard value: 5 - 7 notches
2. If the parking brake lever stroke is not the standard value,
adjust as described below.
(1) Remove the floor console assembly. (Refer to
GROUP52A)
(2) Loosen the adjusting nut to move it to the cable rod
end so that the cable will be free.
(3) Depress the brake pedal repeatedly until the lever
has no change in its stroke.
NOTE
Depressing the brake pedal repeatedly adjusts shoe
clearance correctly.
(4) Turn the adjusting nut to adjust the parking brake lever
stroke to the standard value. After adjusting, check
that there is no space between the adjusting nut and
the parking brake lever. Check that the adjusting nut is
secured with the nut holder.
Caution
If the parking brake lever stroke is below the
standard value and the braking is too firm, the
rear brakes may drag.
(5) After adjusting the parking brake lever stroke, jack
up the rear end of the vehicle, and then release the
parking brake and turn the rear wheels to check that
the rear brakes are not dragging.
PARKING BRAKE SWITCH CHECK
1. Remove the floor console assembly. (Refer to
GROUP52A)
2. Remove the front seat assembly(RH). (Refer to
GROUP52A)
3. Check for continuity between the parking brake switch
terminal and the switch mounting bolt.
When parking brake lever is pulled
Continuity
When parking brake lever is released
No continuity
Adjusting nut
Cable rod
PARKING BRAKES -
On-Vehicle Service
36-4
LINING RUNNING-IN
Carry out running-in by the following procedure when replacing
the parking brake linings or the rear brake disc rotors, or
when brake performance is insufficient.
Caution
Carry out running-in in a place with good visibility, and
pay careful attention to safety.
1. Adjust the parking brake stroke to the specified value.
Standard value [Operation force: Approx. 200 N] :
5 - 7 notches
2. Hook a spring balance onto the centre of the parking
brake lever grip and pull it with a force of 100 - 150
N in a direction perpendicular to the handle.
3. Drive the vehicle at a constant speed of 35 - 50 km/h
for 100 metres.
4. Release the parking brake and let the brakes cool for
5 - 10 minutes.
5. Repeat the procedure in steps 2 to 4 four or five times.
Pull
Spring balance
Approx.
40 mm
PARKING BRAKES -
Parking Brake Lever
36-5
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
Pre-removal Operation
Rear Floor Console Assembly and Rear Console
Bracket Removal (Refer to GROUP 52A-Floor Console.)
Post-installation Operation
D
Parking Brake Lever Stroke Adjustment
(Refer to P.36-3.)
D
Rear Floor Console Assembly and Rear Console
Bracket Installation (Refer to GROUP 52A-Floor
Console.)
5
4
3
2
1
Ratchet plate
Section A - A
Section B - B
Ratchet
pawl
A
B
A
B
Removal steps
1. Adjusting nut
2. Parking brake switch connector
3. Parking brake cable connection
4. Parking brake lever assembly
5. Parking brake switch
PARKING BRAKES -
Parking Brake Cable
36-6
PARKING BRAKE CABLE
REMOVAL AND INSTALLATION
CAUTION
If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched. And if there is
brake fluid on the caliper, wipe out quickly.
Pre-removal Operation
D
Rear Floor Console Assembly and Rear Console
Bracket Removal (Refer to GROUP 52A-Floor
Console.)
D
Rear Seat Cushion Assembly Removal (Refer to
GROUP 52A-Seat.)
Post-installation Operation
D
Parking Brake Lever Stroke Check and Adjustment
(Refer to P.36-3.)
D
Rear Seat Cushion Installation (Refer to GROUP
52A-Seat.)
D
Rear Floor Console Assembly and Rear Console
Bracket Installation (Refer to GROUP 52A-Floor
Console.)
1
Removal steps
D
Shoe and lining assembly
(Refer to P.36-7.)
D
Parking brake cable connection
(Refer to P.36-5.)
1. Parking brake cable
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст