Mitsubishi Lancer Evolution 7. Manual — part 298
POWER PLANT MOUNT - Crossmember
32-9
<L.H. drive vehicles>
35
±
5 N·m
*
1
108
±
10 N·m
52
±
7 N·m
*
1
18
±
2 N·m
70
±
10 N·m
25
±
4 N·m
21
±
4 N·m
49
±
10 N·m
167
±
9 N·m
1
4
5
8
6
7
186
±
10 N·m
*
2
57
±
7 N·m
9
11
12
13
21
±
4 N·m
15
±
3 N·m
10
39
±
5 N·m
39
±
5 N·m
2
3
Removal steps
1. Lower arm and knuckle connection
2. Stabilizer link
A
A"
3. Lower arm assembly
4. Steering shaft assembly and gear
box connecting bolt
5. Rear roll stopper connection bolt
6. Rear roll rod assembly and rear
roll rod bracket
7. Return hose and return pipe
8. Pressure hose connection
A
B"
9. Tie rod end and knuckle connec-
tion
A
C"
10. Crossmember assembly
"
AA 11. Stabilizer bar
12. Steering gear and linkage
13. Crossmember
POWER PLANT MOUNT - Crossmember
32-10
<R.H. drive vehicles>
35
±
5 N·m
*
1
108
±
10 N·m
52
±
7 N·m
*
1
18
±
2 N·m
69
±
9 N·m
25
±
4 N·m
21
±
4 N·m
49
±
10 N·m
167
±
9 N·m
1
3
4
5
8
9
10
11 12
6
7
186
±
10 N·m
*
2
15
±
3 N·m
13
2
39
±
5 N·m
39
±
5 N·m
57
±
7 N·m
21
±
4 N·m
Removal steps
1. Lower arm and knuckle connection
2. Stabilizer link
A
A"
3. Lower arm assembly
4. Pressure hose connection
5. Return hose connection
6. Steering shaft assembly and gear
box connecting bolt
A
B"
7. Tie rod end and knuckle connec-
tion
8. Rear roll stopper connection bolt
A
C"
9. Crossmember assembly
10. Rear roll stopper
"
AA 11. Stabilizer bar
12. Steering gear and linkage
13. Crossmember
POWER PLANT MOUNT - Crossmember
32-11
REMOVAL SERVICE POINTS
A
A" LOWER ARM ASSEMBLY REMOVAL
Lift the transmission with a transmission jack, and then
withdraw the front mounting bolt on the left lower arm
assembly.
A
B"TIE ROD END AND KNUCKLE DISCONNECTION
Caution
1. The thread on the ball joint may be damaged. Do
not remove the tie rod end mounting nut from the
ball jo
int. Just loosen the nut. For this operation, use
the special tool.
2. Suspend the special tool with a cord to prevent it
from dropping.
A
C" CROSSMEMBER ASSEMBLY REMOVAL
Retain the crossmember with a transmission jack, and then
remove the crossmember mounting bolt.
INSTALLATION SERVICE POINT
"
AASTABILIZER BAR INSTALLATION
Align the identification colour on the left side of the stabilizer
bar with the right end of the bushing.
INSPECTION
D
Check the crossmember for cracks and damage.
Wooden block
Transmission jack
Mounting bolt
Cord
Ball joint
MB990635
MB991113 or
MB991406
Nut
Wooden
block
Transmission
jack
Identification
colour
Outside of
vehicle
Bushing
Fixture
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст