Mitsubishi Lancer Evolution 7. Manual — part 296
32-1
POWER PLANT
MOUNT
CONTENTS
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
ENGINE ROLL STOPPER, CENTERMEMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring, and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).
POWER PLANT MOUNT - General Information
32-2
GENERAL INFORMATION
Inertia principal axes system is incorporated into
the engine mount system.
Upper installation of roll mount reduces engine
rolling, and increase of insulator bore also reduces
idle vibration.
CONSTRUCTION DIAGRAM
<Engine mount, Transmission mount>
Transmission mount
Engine mount
<Engine roll stopper, Centermember, Crossmember: L.H. drive vehicles>
Rear roll rod bracket
Front roll stopper
Front roll mount bracket
Rear roll mount bracket
Crossmember
Crossmember bar
Centermember
Rear roll rod assembly
POWER PLANT MOUNT - General Information/Special Tool
32-3
<Engine roll stopper, Centermember, Crossmember: R.H. drive vehicles>
Front roll stopper
Front roll mount bracket
Rear roll stopper
Rear roll mount bracket
Crossmember
Crossmember bar
Centermember
SPECIAL TOOL
Tool
Number
Name
Use
MB990635
,
MB991113 or
MB991406
Steering linkage
puller
Tie rod end disconnection
POWER PLANT MOUNT - Engine Mounting
32-4
ENGINE MOUNTING
REMOVAL AND INSTALLATION
Caution
*: Indicates parts which should be initially tightened, and then fully tightened after placing the
vehicle horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal and Post-installation Operation
D
Under Cover Removal and Installation (Refer to
GROUP 51 - Front Bumper.)
D
Raise the engine and transmission assembly until
its weight is not applied to the insulator, and support
it securely. <After installation only>
98
±
10 N·m
*
67
±
7 N·m
*
1
2
12
±
2 N·m
3
4
4
Removal steps
1. Power steering pressure hose as-
sembly
2. Engine mounting connecting bolt
3. Engine mounting bracket
"
AA 4. Engine mounting insulator
INSTALLATION SERVICE POINT
"
AA ENGINE MOUNTING INSULATOR INSTALLATION
Arrow marks on the engine mount insulator should face the
shown direction.
NOTE
Disregard F and R stamped as a shared part.
Engine side
Engine side
Engine mounting insulator
<Vehicle rear view
>
<Vehicle front view
>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст