Mitsubishi Lancer Evolution 7. Manual — part 148
ENGINE -
Camshaft and Camshaft Oil Seal
11A-17
2
3
4
5
6
7
8
9
10
12
11
11 ± 1 N·m
8.8 ± 1.0 N·m
3.5 ± 0.5 N·m
5.0 ± 1.0 N·m
13
3.0 ± 0.5 N·m
1
11 ± 1 N·m
Removal steps
1. Accelerator cable connection
<L.H. drive vehicles>
2. Center cover
D
Ignition coil
(Refer to Group 16 - Ignition System.)
3. Crank angle sensor connector
4. Oxygen sensor connector
5. Control wiring harness connection
6. Camshaft position sensor connector
7. Breather hose
8. PCV hose
"
KA 9. Rocker cover
"
JA 10. Camshaft end seal
11. Spark plug hole gasket
"
IA 12. Rocker cover gasket
A
A" "HA 13. Radiator upper hose connection
ENGINE -
Camshaft and Camshaft Oil Seal
11A-18
Apply engine oil to all
sliding parts at the time
of installation.
10 ± 2 N·m
89 ± 9 N·m
20 ± 1 N·m
22 ± 4 N·m
14 ± 1 N·m
28
29
27
26
20
14
15
16
17
19
18
22
23
21
24
25
11 ± 1 N·m
30
14. Camshaft position sensor support
cover
15. Camshaft position sensor support
cover gasket
"
GA 16. Camshaft position sensing cylinder
"
FA 17. Camshaft position sensor support
A
B" "EA 18. Camshaft sprocket
"
DA 19. Camshaft oil seal
"
CA 20. Camshaft bearing cap front
"
CA 21. Camshaft bearing cap rear
"
CA 22. Camshaft bearing cap No. 2
"
CA 23. Camshaft bearing cap No. 5
"
CA 24. Camshaft bearing cap No. 3
"
CA 25. Camshaft bearing cap No. 4
"
BA 26. Intake camshaft
"
BA 27. Exhaust camshaft
28. Rocker arm
"
AA 29. Lash adjuster
30. Oil delivery body
ENGINE -
Camshaft and Camshaft Oil Seal
11A-19
LUBRICATION AND SEALING POINTS
10 mm
10 mm
Sealant: MITSUBISHI GENUINE PART MD970389 or equivalent
<Top View of cylinder head>
(at the lip)
Engine oil
10 mm
Sealant: MITSUBISHI GENUINE
PART MD970389 or equivalent
Sealant: MITSUBISHI GENUINE PART MD970389 or equivalent
<The bottom view of the rocker cover>
Sealant:
MITSUBISHI GENUINE
PART MD970389 or
equivalent
10 mm
10 mm
<View A>
A
A
A
Rocker
cover
Cylinder
head
ø3 mm
Sealant: 3M ATD Part No.8660
or equivalent
ENGINE -
Camshaft and Camshaft Oil Seal
11A-20
REMOVAL SERVICE POINTS
A
A" RADIATOR UPPER HOSE DISCONNECTION
Indicate the mating marks on the radiator upper hose and
the hose clamp for release.
A
B" CAMSHAFT SPROCKET REMOVAL
Hold the hexagon part of the camshaft with a wrench and
loosen the mounting bolt, then remove the camshaft sprocket.
INSTALLATION SERVICE POINTS
"
AA LASH ADJUSTER INSTALLATION
Caution
When the lash adjuster is reused, always install it after
cleaning and inspecting.
(Refer to GROUP 11B - Rocker Arms and Camshaft.)
"
BA EXHAUST CAMSHAFT/INTAKE CAMSHAFT
INSTALLATION
1. Remove sealant remained on the cylinder head.
2. Apply engine oil to the cam and the journal of the camshaft.
3. Install the camshaft to the cylinder head.
Caution
Do not install wrong camshaft at the side of intake
or exhaust.
The exhaust camshaft has a slit at the rear surface.
"
CA CAMSHAFT BEARING CAP NO.4/CAMSHAFT
BEARING CAP NO.3/CAMSHAFT BEARING CAP
NO.5/CAMSHAFT BEARING CAP NO.2/
CAMSHAFT BEARING CAP REAR/CAMSHAFT
BEARING CAP FRONT INSTALLATION
1. Set the dowel pin of the camshaft to the position as shown
in the illustration.
Engine Front
Exhaust
camshaft
Slit
Dowel Pin
Approximately 3_
Intake Side
Exhaust Side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст