Mitsubishi Evolution X. Manual — part 865
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-17
PARKING BRAKE LINING AND DRUM
REMOVAL AND INSTALLATION
M1361002500746
Post-installation Operation
• Parking Brake Lever Stroke Adjustment (Refer to
• Lining Running-in (Refer to
AC709255
15
17
9
21
18
19
20
2
22
4
5
9
22
8
13
14
15
10
11
12
6
7
13
14
1
AB
3
17
16
Specified grease: Chuo Yuka AKB 100 or equivalent
11 ± 2 N·m
98 ± 17 in-lb
80 ± 10 N·m
59 ± 7 ft-lb
145 ± 15 N·m
107 ± 11 ft-lb
Removal steps
•
Release the parking brake lever.
1.
Adjusting hole plug
2.
Brake hose bracket connection
<<
A
>>
3.
Rear brake caliper assembly
<<
B
>>
4.
Rear brake disc
>>
D
<<
5.
Shoe-to-anchor spring
>>
D
<<
6.
Shoe-to-anchor spring
7.
Shoe guide plate
8.
Adjusting wheel spring
>>
C
<<
9.
Adjuster assembly
10. Strut
11. Strut shoe-to-spring
12. Shoe hold down pin
13. Shoe hold down cup
14. Shoe hold down spring
15. Shoe and lining assembly
16. Parking brake rear cable
connection
17. Shoe and lever assembly
>>
B
18. Chamber retainer
>>
A
19. Washer
20. Parking brake operating lever
21. Shoe and lining assembly
Removal steps (Continued)
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-18
REMOVAL SERVICE POINTS
.
<<A>> REAR BRAKE CALIPER ASSEMBLY
REMOVAL
1. Remove the rear brake caliper assembly with the brake
hose kept attached.
2. Secure the removed rear brake caliper assembly with a wire
or other similar material at a position where it will not
interfere with the removal and installation works.
.
<<B>>REAR BRAKE DISC REMOVAL
AC707776AB
Bolts (M8 x 1.25 mm)
If the rear brake disc removal is difficult, install bolts (M8 x 1.25
mm) shown in the figure, and tighten them evenly and gradually
to remove the rear brake disc.
INSTALLATION SERVICE POINTS
.
>>A<< WASHER INSTALLATION
AC304675AD
Shoe and lining assembly
Chamber
retainer
Washer
Parking brake
operating lever
Install the washer in the direction shown in the illustration.
.
>>B<< CHAMBER RETAINER INSTALLATION
AC000926AJ
Pin of shoe and lining assembly
Chamber retainer
Use pliers or a similar tool to close the chamber retainer end
onto the pin.
.
•
Rear wheel hub assembly (Refer to
GROUP 27 - Rear Axle Hub
Assembly
22. Backing plate
Removal steps (Continued)
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-19
>>C<< ADJUSTER ASSEMBLY INSTALLATION
AC706498AB
Shoe adjusting bolt
Shoe adjusting bolt
<Right side wheel>
<Left side wheel>
Front of the vehicle
Rear of the vehicle
Install the adjuster assembly so that the shoe adjusting bolt is
positioned at the rear of the vehicle for the left side, and at the
front of the vehicle for the right side.
.
>>D<< SHOE-TO-ANCHOR SPRING
INSTALLATION
AC706198 AB
Front of the vehicle
Blue paint
Yellow paint
Blue paint
Yellow paint
<Right side wheel>
<Left side wheel>
The shoe-to-anchor springs are not interchangeable because
their spring loads are different. The one with blue paint must be
installed to the vehicle front, and the other with yellow paint to
the vehicle rear.
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-20
INSPECTION
M1361002600538
BRAKE LINING THICKNESS CHECK
ACX00708
1. Measure the lining thickness at the most worn area.
Standard value: 2.8 mm (0.11 inch)
Limit: 1.0 mm (0.04 inch)
2. If the thickness is less than the limit value, replace the right
and left shoe and lining assemblies as a set.
BRAKE DRUM INSIDE DIAMETER CHECK
ACX00709
1. Measure the inside diameter of the brake drum at two
positions or more.
Standard value: 190.0 mm (7.48 inch)
Limit: 191.0 mm (7.52 inch)
2. If the inside diameter is more than limit value or if there is
excessive wear, replace the brake disc.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст