Mitsubishi Evolution X. Manual — part 846
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-67
Required Special Tool:
• MB991958: M.U.T.-III sub-assembly
• MB991223: Harness set
• MB992006: Extra fine probe
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
AC709005
C
8
6
4
C
A
A
D
D
E
E
F
F
4
6
6
7
7
AB
B
4
5
5
8
6
7
6
4
4
B
Section B – B
Section C – C
: Clip positions
Hood
Section A – A
Section D – D
Boss
Bolt
Clip
Claw
Claw
Claw
Section E – E
Section F – F
Hood
Windshield
Windshield
Wind-
shield
Windshield
Wiper blade removal steps
>>
C
<<
1.
Wiper blade assembly
>>
A
<<
2.
Wiper blade
Windshield wiper motor and
wiper link assembly removal
steps
>>
C
<<
3.
Wiper arm
4.
Front deck garnish cover A
5.
Hood weatherstrip
6.
Front deck garnish
7.
Front deck garnish cover B
8.
Front deck cover
<<
A
>>
>>
B
<<
9.
Wiper link assembly
<<
B
>>
10. Wiper motor link plate
<<
B
>>
11. Windshield wiper motor
Windshield wiper motor and
wiper link assembly removal
steps (Continued)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-68
REMOVAL SERVICE POINTS
.
<<A>> WIPER LINK ASSEMBLY REMOVAL
1. Manually turn the link rod of the wiper link assembly forward
to the position indicated in the figure.
CAUTION
Another mechanic fully pushes up the hood so that the left
side of link assembly is pulled out easily.
2. Pull out the attachment section of the left side of wiper link
assembly forward until the link rod bumps against the front
deck garnish retainer.
CAUTION
When pulling out the link assembly forward, be careful not
to make a contact with the windshield glass.
3. While turning the link assembly upward (A), pull out the
entire link assembly diagonally forward left (B).
.
AC609130AE
Link rod
<Right>
<Front>
<Left>
1
2
3
Wiper link assembly
(A)
(B)
Front deck garnish retainer
Link rod
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-69
<<B>> WIPER MOTOR LINK PLATE/WINDSHIELD
WIPER MOTOR REMOVAL
1. To disconnect the wiper motor link plate from the wiper
motor shaft, use an appropriate tool to counter-hold the
plate to prevent it from turning.
2. Remove the wiper motor from the wiper link assembly.
INSTALLATION SERVICE POINTS
.
>>A<< WIPER BLADE INSTALLATION
CAUTION
For good windshield wiper wiping performance, use wind-
shield wipers without a curve in the backing of the wiper
blade.
.
>>B<< WIPER LINK ASSEMBLY/WIPER MOTOR
LINK PLATE/WINDSHIELD WIPER MOTOR
INSTALLATION
1. Confirm that the wiper motor has set to automatic stop
position (Refer to
).
CAUTION
Always replace the wiper motor link plate with new one.
2. Set the wiper motor link plate onto the wiper motor shaft;
aligning the triangle mark on the plate to the center line (of 3
lines) on the wiper link assembly as shown in the illustration.
3. Tighten the attaching nut of wiper motor link plate and wiper
motor shaft. Use an appropriate tool to counter-hold the
plate to prevent it from turning.
4. Apply grease to the inside of link rod joint (as required) and
connect the link rod to wiper motor link plate.
Specified grease: Multipurpose grease SAE J310,
NLGI No.2 or equivalent
.
AC609250
AB
Wiper motor
link plate
AC609740
AB
A
A
Wiper blade
Backing
Backing
Section A – A
Wiper
blade
Backing
AC609252
AB
Wiper motor
link plate
Link rod
Link rod joint
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-70
>>C<< WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Set the wiper arm and blade assembly at the specified posi-
tions.
A(Passenger’s side): Ceramic end line
± 5 mm(0.20 in)
B(Driver’s side): Front deck garnish end
45
± 5 mm (1.77 ± 0.20 in)
INSPECTION
M1511008000317
WINDSHIELD WIPER MOTOR CHECK
The windshield wiper motor assembly should be installed to
the vehicle body and the harness connector should be discon-
nected when checking the wiper motor.
.
WINDSHIELD WIPER MOTOR AT LOW OR HIGH
SPEED OPERATION
Connect the battery to the windshield wiper motor to inspect
the operation of motor rotation at low or high speed.
AC612983AD
A
Section A – A
Front deck garnish
B
Ceramic end
line
B
A
Front deck garnish
Wiper arm and blade
assembly
Ceramic end
line
Wiper blade
Ceramic end
line
Section B – B
Front deck garnish
retainer end
Wiper blade
45 (1.77)
Unit: mm (in)
Unit: mm (in)
5 (0.20)
5 (0.20)
5 (0.20)
5 (0.20)
4 5
3
1 2
4 5
3
1 2
4 5
3
1 2
AC608787AB
Operation check
Low speed
High speed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст