Mitsubishi Evolution X. Manual — part 845
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-63
STEP 8. Check the wiring harness between windshield
washer motor connector D-20 (terminal 2) and ETACS-ECU
connector C-304 (terminal 13).
• Check the input lines for open or short circuit.
Q: Is the wiring harness between windshield washer motor
connector D-20 (terminal 2) and ETACS-ECU connector
C-304 (terminal 13)in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Cables and wire check
.
STEP 9. Check the wiring harness between windshield
washer motor connector D-20 (terminal 1) and ETACS-ECU
connector C-304 (terminal 14).
NOTE: Prior to the wiring harness inspection, check intermedi-
ate connector C-47 and repair if necessary.
• Check the input lines for open or short circuit.
Q: Is the wiring harness between windshield washer motor
connector D-20 (terminal 1) and ETACS-ECU connector
C-304 (terminal 14)in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Cables and wire check
.
STEP 10. Retest the system.
Check that the windshield washers work normally.
Q: Is the check result normal?
YES : Intermittent malfunction. Refer to GROUP 00, How to
cope with intermittent malfunction
.
NO : Replace the ETACS-ECU.
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-64
DATA LIST REFERENCE TABLE
M1511015100048
LIN (LIGHTING CONTROL SENSOR)
ON-VEHICLE SERVICE
WINDSHIELD INTERMITTENT WIPER INTERVAL CHECK
M1511023600112
1. Check that the intermittent wiper interval is
changed as the windshield intermittent wiper
interval control is operated.
2. Turn the windshield intermittent wiper switch to
the intermittent operation position. Use scan tool
MB991958 to set a simulated vehicle speed with
the wiper volume held. The intermittent wiper
interval should be changed as the simulated vehi-
cle speed is changed.
3. If either of above is defective, carry out the trou-
)
Item No. Scan tool display
Check condition
Normal condition
7005
RLS Rain sensor ON/OFF
When the wiper switch is AUTO position
ON
When a switch (except the wiper switch) is
AUTO position
OFF
7006
RLS Rain sensor sensitivity Changes from 1 to 5 according to the
wiper volume.
1, 2, 3, 4, 5
7008
RLS Wiper auto stop SW
When the windshield wiper is in operation Park
Other than above
Outside park
7013
RLS Wiper control output
When the operation is not requested from
lighting control sensor (rain sensor).
OFF
When the LO operation is requested from
lighting control sensor (rain sensor)
LO
When the HI operation is requested from
lighting control sensor (rain sensor)
HI
7020
RLS RS measurement
value(RS1)
When the lighting control sensor (rain
sensor) detects raindrops
The sensor 1 detects
raindrops and the
value changes.
7021
RLS RS measurement
value(RS2)
When the lighting control sensor (rain
sensor) detects raindrops
The sensor 2 detects
raindrops and the
value changes.
7022
RLS RS adaptation
value(RS1)
When initializing after the adaptation
(sensor 1)
The amount of output
when initializing
(sensor 1)
7023
RLS RS adaptation
value(RS2)
When initializing after the adaptation
(sensor 2)
The amount of output
when initializing
(sensor 2)
7024
RLS RS adaptation gain
level
When initializing after the adaptation
The calibrated value of
initializing
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-65
LIGHTING CONTROL SENSOR (RAIN SENSOR) INSPECTION
M1511028400049
Under clear weather (windshield glass is dry), turn
the ignition switch to "ON" position and wiper switch
to "AUTO" position. Check that the wiper works when
applying water to the upper part of the windshield
glass where the lighting control sensor is installed. If
there is a malfunction, perform the troubleshooting
(Refer to
).
CONFIGURATION FUNCTION
M1511027400251
Using the ETACS system of scan tool MB991958,
the following functions can be programmed. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Front wiper
operation
Adjustment of the
intermittent
windshield wiper
operation <vehicles
without auto light>
Normal INT
Intermittent wiper interval is fixed to 4
seconds.
Variable INT
Intermittent wiper interval is calculated only
by the wiper volume control.
Speed Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed (default).
Adjustment of the
intermittent
windshield wiper
operation <vehicles
with auto light>
Normal INT
Intermittent wiper interval is fixed to 4
seconds.
Variable INT
Intermittent wiper interval is calculated only
by the wiper volume control.
Speed Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed.
Rain Sensitive
Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and lighting control sensor
(default).
Front wiper
washer
Disabling or
enabling
washer-linked wiper
function
Only washer
No function
Washer&wiper
With function (default)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-66
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007900834
AC708712AB
5
11
4
10
8
9
6
11
A
Specified grease: Multipurpose
grease SAE J310, NLGI No. 2 or
equivalent
27 ± 3 N·m
20 ± 2 ft-lb
27 ± 3 N·m
20 ± 2 ft-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
9
4
10
2
3
1
2
1
3
5
7.4 ± 1.4 N·m
65 ± 13 in-lb
31 ± 2 N·m
24 ± 1 ft-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
Section B – B
BB
BB
<Front>
7
N
N
View A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст