Mitsubishi Evolution X. Manual — part 324
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-71
13. TRANSFER OIL (CHECK OIL LEVEL/CHANGE)
M1001003000208
TRANSFER OIL CHECK
1. Remove the engine room under cover front B assembly.
(Refer to GROUP 51
.)
2. Remove the oil filler plug and gasket.
3. Check that the oil level is just below the lower edge of the oil
filler plug hole.
4. Check that the oil is not excessively foul and has moderate
viscosity.
5. Install the oil filler plug and new gasket, then tighten them to
the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 1 ft-lb)
6. Install the engine room under cover front B assembly. (Refer
to GROUP 51
− Under cover
TRANSFER OIL CHANGE
1. Remove the engine room under cover front B assembly.
(Refer to GROUP 51
.)
2. Remove the oil drain plug and gasket to drain the oil.
3. Install the oil drain plug and new gasket, then tighten them
to the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 1 ft-lb)
4. Remove the oil filler plug and gasket, then fill the oil up to
the lower edge of the oil filler plug hole.
Brand name: Mitsubishi genuine Dia-Queen LSD
Gear Oil
Quantity: 0.9 dm
3 (1.0 quarts)
5. Install the oil filler plug and new gasket, then tighten them to
the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 1 ft-lb)
6. Install the engine room under cover front B assembly. (Refer
to GROUP 51
− Under cover
AC704516AE
Oil filler plug
Oil drain plug
Engine oil pan
AC700330AE
Gasket
Transmission oil
Filler plug hole
Oil filler plug
AC704516AE
Oil filler plug
Oil drain plug
Engine oil pan
AC700330AE
Gasket
Transmission oil
Filler plug hole
Oil filler plug
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-72
14. RESERVE TANK FLUID (FOR ACTIVE CENTER
DIFFERENTIAL AND ACTIVE YAW CONTROL
SYSTEM) (CHECK FLUID LEVEL)
M1001017500013
FLUID LEVEL CHECK
.
<WHEN THE SCAN TOOL IS NOT USED>
1. Remove the trunk room side trim lid on the right of the trunk
room.
2. If the vehicle has been run, leave it for 90 min. or more in an
ordinary temperature {10
− 30° C (50 − 86° F)} to allow the
accumulator internal pressure to drop.
NOTE: If the ambient temperature is 10
°
C (50
°
F) or less,
allow more time to leave the vehicle to stand idle.
3. Check that the oil reservoir fluid level is in between MAX and
MIN.
4. If the fluid level is not in between MAX and MIN, fill the
specified fluid.
Specified fluid: DIAMOND ATF-SP III
5. Install the trunk room side trim lid.
.
<WHEN THE SCAN TOOL IS USED>
1. Remove the trunk room side trim lid on the right of the trunk
room.
CAUTION
Turn the ignition switch to the "LOCK (OFF)" position
before connecting or disconnecting the scan tool.
2. Set the scan tool to the 16-pin data link connector. (Refer to
.)
3. Turn the ignition switch to the ON position.
4. Using the scan tool, forcibly activate the hydraulic unit (item
No. 03) to reduce the pressure inside the accumulator.
(Refer to GROUP 22A
− Actuator Test Table.)
NOTE:
.
•
With the forced activation (oil level check mode), the
hydraulic unit direction valve is operated 20 times to right
and left, and then the operation is canceled automati-
cally. Also, using the clear key on the scan tool, the acti-
vation can be forcibly canceled.
•
When the functions are suspended by the fail-safe func-
tion, the hydraulic unit cannot be forcibly activated.
AC705200AB
Oil reservoir
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-73
5. Check that the oil reservoir fluid level is in between MAX and
MIN.
6. If the fluid level is not in between MAX and MIN, fill the
specified fluid.
Specified fluid: DIAMOND ATF-SP III
7. Install the trunk room side trim lid.
15. ENGINE COOLANT (CHANGE)
M1001003100573
1. Remove the engine room under cover front A (RH). (Refer to
GROUP 51, Under Cover
WARNING
When removing the radiator cap, use care to avoid
contact with hot coolant or steam. Place a shop towel
over the cap and turn the cap counterclockwise a lit-
tle to let the pressure escape through the vinyl tube.
After relieving the steam pressure, remove the cap by
slowly turning it counterclockwise.
2. Drain the water from the radiator, heater core and engine
after unplugging the radiator drain plug and removing the
radiator cap.
3. Remove the engine room under cover front B. (Refer to
GROUP 51, Under Cover
4. Remove the air cleaner intake hose. (Refer to GROUP 15,
Air Cleaner
)
5. Remove the turbocharger compressor bracket. (Refer to
GROUP 15, Exhaust Manifold and Turbocharger Assembly
)
6. Disconnect the turbocharger water return hose and drain the
coolant in the water jacket.
7. Remove the radiator condenser tank and drain the coolant.
8. Drain the coolant then clean the path of the coolant by
injecting water into the radiator from the radiator cap area.
9. Securely tighten the drain plug of the radiator.
10.Reinstall the radiator condenser tank.
AC705200AB
Oil reservoir
AC706501AC
Turbo charger
air inlet fitting
Turbo charger
water return hose
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-74
CAUTION
Do not use alcohol or methanol anti-freeze or any engine
coolants mixed with alcohol or methanol anti-freeze. The
use of an improper anti-freeze can cause corrosion of the
aluminum components.
11.By referring to the section on coolant, select an appropriate
concentration for safe operating temperature within the
range of 30 to 60%. Use special tool MB991871 to refill the
engine coolant up to the top of the radiator port. A
convenient mixture is a 50% water and 50% antifreeze
solution [freezing point:
−31° C (−23.8 ° F)].
Recommended antifreeze: Long Life Antifreeze
Coolant or an equivalent
Quantity: 7.5 dm
3
(7.9 quarts)
NOTE: For how to use special tool (MB991871), refer to its
manufacturer’s instructions.
12.Tighten the radiator cap securely.
13.Remove the radiator condenser tank cap, and add the
engine coolant up to the "FULL" line.
14.Turn the A/C switch to OFF position to start the engine and
warm up until the cooling fan operates.
NOTE: This step opens the thermostat fully.
15.Rev the engine several times and then stop it. Check that
there are no coolant leaks.
16.Remove the radiator cap with the engine cool, and then refill
the engine coolant up to the top of the radiator port.
17.Tighten the radiator cap securely.
CAUTION
Do not overfill the radiator condenser tank.
18.Remove the radiator condenser tank cap, and add the
engine coolant up to the "FULL" line.
19.Install the turbocharger compressor bracket. (Refer to
GROUP 15, Exhaust Manifold and Turbocharger Assembly
)
20.Install the air cleaner intake hose. (Refer to GROUP 15, Air
Cleaner
21.Remove the engine room under cover front A and engine
room under cover front A (RH). (Refer to GROUP 51, Under
Cover
16. COOLANT HOSES (RADIATOR HOSE,
HEATER HOSE) (INSPECT)
M1001009700175
Inspect the surface of radiator hoses and heater hoses for heat
and mechanical damage. Hard and brittle rubber, cracking,
tears, cuts, abrasions and excessive swelling indicate deterio-
ration of the rubber.
AC705466AC
MB991871
Air hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст