Mitsubishi Evolution X. Manual — part 323
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-67
8. EXHAUST SYSTEM (CONNECTIONS PORTION
OF MUFFLER, MUFFLER PIPES AND
CONVERTER HEAT SHIELDS) (CHECK AND
SERVICE)
M1001005800459
Check for holes and exhaust gas leaks due to damage,
corrosion, etc.
1. Check the joints and connections for looseness and exhaust
gas leaks.
2. Check the rubber hangers and brackets for damage.
9. ENGINE OIL (CHANGE)
M1001002600661
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90° C (176 −
194
° F).
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the engine room under cover extension. (Refer to
GROUP 51, Under Cover
4. Remove the drain plug to drain oil.
5. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39
± 5 N⋅ m (29 ± 3 ft-lb)
CAUTION
• Do not use conventional petroleum based motor oil.
Using conventional motor oil may cause engine or tur-
bocharger damage.
• Do not used "blends" of conventional oil and synthetic
oil.
• If engine oil other than 5W-30 is used, the engine may
be seized by poor lubrication.
6. Refill the specified quantity of oil.
Specified Engine Oil: Engine oils displaying ILSAC
certification symbol ("Starburst" symbol) or con-
forming to the API classification SM or higher
Total quantity: 5.6 dm
3
(5.9 quarts)
7. Install the engine oil filler cap.
8. Let the engine run for a few minutes.
9. Stop the engine, and then check the oil level using the oil
dipstick after a few minutes.
10.Install the engine room under cover extension. (Refer to
GROUP 51, Under Cover
AC708804AB
Engine
oil pan side
Drain plug gasket
AC710765AB
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-68
10. ENGINE OIL FILTER (REPLACE)
M1001002700594
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90° C (176 − 194° F)
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the engine room under cover extension (Refer to
GROUP 51, Under Cover
4. Remove the drain plug to drain oil.
5. Use the respective tool in the following table to remove the
engine oil filter.
6. Clean the filter bracket side mounting surface and ensure
the old O-ring has been removed.
7. Apply a small amount of engine oil to the O-ring of the new
oil filter.
8. Screw on the oil filter by hand until it touches the surface of
the flange and then tighten it with an oil filter wrench.
9. Install the drain plug and refill engine oil (Refer to
10.Rev the engine a few times, and check to be sure that no
engine oil leaks at the oil filter.
11.Install the engine room under cover extension (Refer to
GROUP 51, Under Cover
11. MANUAL TRANSAXLE OIL (CHECK OIL
LEVEL AND CONDITION/RCHANGE)
M1001006100118
TRANSAXLE OIL LEVEL CHECK
1. Remove the engine room under cover front B assembly.
(Refer to GROUP 51
.)
Number
Special tool
MD356000
Oil filter wrench
(MB991610) or
equivalent
Number
Special tool
Tightening
torque
MD356000
MB991610 or
equivalent
Approximately
3/4 turn [14
± 2
N
⋅ m (124 ± 17
in
−lb)]
AC103249AL
MB991610
or equivalent
AC103250 AG
O-ring
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-69
2. Remove the oil filler plug and gasket.
3. Check that the oil level is just below the lower edge of the oil
filler plug hole.
4. Check that the oil is not excessively foul and has moderate
viscosity.
5. Install the oil filler plug and new gasket, then tighten them to
the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 1 ft-lb)
6. Install the engine room under cover front B assembly. (Refer
to GROUP 51
− Under cover
TRANSAXLE OIL CHANGE
1. Remove the engine room under cover front B assembly.
(Refer to GROUP 51
.)
2. Remove the oil drain plug and gasket to drain the oil.
3. Install the oil drain plug and new gasket, then tighten them
to the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 2 ft-lb)
4. Remove the oil filler plug and gasket, then fill the oil up to
the lower edge of the oil filler plug.
Brand name: Mitsubishi genuine Dia-Queen New Multi
Gear Oil SAE 75W-80 API GL-3
Quantity: 2.5 dm
3
(2.6 quarts)
5. Install the oil filler plug and new gasket, then tighten them to
the specified torque.
Tightening torque: 32
± 2 N⋅ m (24 ± 1 ft-lb)
6. Install the engine room under cover front B assembly. (Refer
to GROUP 51
− Under cover
AC707416AC
Center member
Centermember
Oil filler plug
Oil drain plug
AC700330AE
Gasket
Transmission oil
Filler plug hole
Oil filler plug
AC707416AC
Center member
Centermember
Oil filler plug
Oil drain plug
AC700330AE
Gasket
Transmission oil
Filler plug hole
Oil filler plug
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-70
12. TWIN CLUTCH SPORTRONIC SHIFT
TRANSMISSION [CHECK OIL LEAKS (IF
NECESSARY, CHECK THE OIL LEVEL) /CHANGE]
M1001016600017
TC-SST OIL LEVEL CHECK
1. After cleaning the outer surface of transaxle, visually check
that there is no oil oozing or oil leaking from the transaxle.
2. If an oil oozing or leaking is present, replace the transaxle
assembly.
TC-SST OIL CHANGE
1. Remove the engine compartment under cover front B
assembly. (Refer to GROUP 51
− Under Cover
.)
2. Remove the oil drain plug to drain the oil.
NOTE: Because the oil in the oil cooler and oil filter cannot
be drained, the amount of drained oil will be approximately
5.5 dm
3
.
3. Tighten the oil drain plug to the specified torque.
Tightening torque: 25 N
⋅ m
4. Remove the air cleaner element, air cleaner intake duct, and
air cleaner body. (Refer to GROUP 15
− Air Cleaner
.)
5. Remove the oil filler plug, then fill the oil.
Brand name: Mitsubishi genuine Dia-Queen SSTF-I
Filling amount: Approximately 5.5 dm
3
6. Tighten the oil filler plug to the specified torque.
Tightening torque: 25 N
⋅ m
7. Install the air cleaner element, air cleaner intake duct, and
air cleaner body. (Refer to GROUP 15
− Air Cleaner
.)
8. Start the engine, then let it idle for 1 to 2 minutes.
9. Move the shift lever to every position, and then move it to
the P or N range.
10.Stop the engine, then perform Steps 2 to 5 again.
11.Check the oil level and oil fouling. (Refer to
fouling is found, repeat Steps 2 to 5 until the fouling is
eliminated.
12.Install the engine compartment under cover front B
assembly. (Refer to GROUP 51
− Under Cover
.)
AC704517AC
Oil drain plug
Centermember
AC704813AC
Oil filler plug
Transmission control
lever
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст