Mitsubishi Evolution X. Manual — part 1294
AMBIENT TEMPERATURE SENSOR
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-127
AMBIENT TEMPERATURE SENSOR
REMOVAL AND INSTALLATION
M1554003400487
INSPECTION
M1551006300769
.
AMBIENT AIR TEMPERATURE SENSOR CHECK
CAUTION
The ambient air temperature sensor should be checked
without removing it. If the sensor is removed, it is no
longer serviceable.
Measure the resistance between the sensor terminals under at
least two temperatures. The resistance values should meet the
values shown.
NOTE: The temperature should be within the shown range.
AC605673AI
Horn (low)
1
Removal step
•
Headlight support panel cover
(Refer to GROUP 51, Front bumper
assembly
1.
Ambient air temperature sensor
AC209192
10
8
6
4
2
0
AB
10
(50)
30
(86)
Resistance
(k
Ω)
Temperature ºC (ºF)
0
(32)
40
(104)
-10
(14)
20
(68)
INTERIOR TEMPERATURE SENSOR
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-128
INTERIOR TEMPERATURE SENSOR
REMOVAL AND INSTALLATION
M1554026400046
INSPECTION
M1552014303852
.
INTERIOR TEMPERATURE SENSOR CHECK
When the resistance between the sensor terminals is mea-
sured under two or more temperature conditions, the resis-
tance should approximately satisfy the illustrated values.
NOTE: The temperature conditions when checking should not
exceed the range shown in the diagram.
AC709099
1
2
AB
Claw
1
AC704919
Instrument panel
A
A
Cross-section A-A
Interior temperature sensor
removal steps
•
Lower panel (Refer to GROUP 52A,
Instrument panel
1.
Interior temperature sensor
2.
Aspirator hose
Interior temperature sensor
removal steps (Continued)
AC609165
20
15
10
5
0
AB
10
(50)
30
(86)
Resistance
(k
Ω)
Temperature ºC (ºF)
0
(32)
40
(104)
-10
(14)
20
(68)
A/C-ECU
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-129
A/C-ECU
REMOVAL AND INSTALLATION
M1554016600254
Pre-removal and Post-installation Operation
• Glove Box and Bottom Cover Assembly (passenger's
side) Removal and Installation (Refer to GROUP 52A
−
Instrument Panel
• Foot duct Removal and Installation (Refer to
AC708793
A/C-ECU
AC
COMPRESSOR ASSEMBLY AND TENSION PULLEY
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-130
COMPRESSOR ASSEMBLY AND TENSION PULLEY
REMOVAL AND INSTALLATION
M1552004100610
Pre-removal Operation
• Refrigerant Discharging (Refer to
• Engine room under cover front A (Refer to GROUP 51,
under cover
• Front Under Cover RH (Refer to GROUP 51, Under cover
Post-installation Operation
• Drive Belt Tension Adjustment (Refer to GROUP 11A, On
vehicle service
• Refrigerant Charging (Refer to
).
• Engine room under cover front A (Refer to GROUP 51,
under cover
• Front Under Cover RH (Refer to GROUP 51, Under cover
AC608280
1, 2
3
A/C compressor oil:
SUN PAG 56
-Pipe coupling
6
5
4
1
2
3
3
N
N
23 ± 6 N·m
17 ± 4 ft-lb
25 ± 4 N·m
18 ± 3 ft-lb
25 ± 4 N·m
18 ± 3 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
Removal steps
<<
A
>>
1.
Flexible discharge hose connection
<<
A
>>
2.
Flexible suction hose connection
3.
O-ring
4.
Drive belt
<<
B
>>
>>
A
5.
A/C compressor and clutch
assembly
6.
A/C compressor bracket
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст