Mitsubishi Evolution X. Manual — part 625
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-117
AC611443AE
Keyless ID
Reg.*1
OK
Keyless ID
registration
Executing
Keyless ID
registration
Completed
OK
OK
Steering lock
unit Reg.*2
OK
Steering lock
unit registration
Executing
OK
Antenna select
Antenna
communication
test Executing
NOTE:
*1 Show the menu displayed when the vehicles for WCM.
*2 Show the menu displayed when the vehicles for KOS.
Steering lock
unit registration
Completed
Password input
Registration
result display
Comm.
Test *2
Antenna
communication
test Completed
Password input
A
Tire Pressure
Sensor ID
Registration *1,*2
Tire Pressure
Sensor Check *1,*2
Tire Pressure
Sensor ID
Check *1,*2
ID Check
Sensor Check
Sensor Check
Executing
Check
Sensor Check
Executing
Sensor Check
Completed
Sensor Check
Result Display
Sensor Check
Cancel Check
OK
OK
OK
OK
OK
Cancel
Cancel
Can
cel
ID Registration
Menu
ID Registration
Menu
ID Registration
Executing
Check
ID Registration
Executing
ID Registration
Completed
ID Registration
Cancel Check
ID Registration
Cancel
Completed
Select &
OK
Can
cel
OK
Can
cel
OK
OK
Can
cel
OK
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-118
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
Connect the scan tool to the 16-pin data link connector as fol-
lows.
NOTE: For details on how to use the scan tool, refer to the
"M.U.T.-III User's Manual."
1. Start the scan tool MB991958 system on the personal
computer and turn the ignition switch to the "ON" position.
2. Select "F.A.S.T./IMMO/Keyless/TPMS" button from the
"System Select" screen. Then, select the applicable option
code item and push the OK button.
3. Select "Special Function" on the next screen.
4. Select the button of the operation to be performed from the
"Special Function" screen.
• "Key Registration": When the ignition key is replaced or
added as a single unit and/or the WCM replaced.
• "Additional key registration": When the ignition key is added
as a single unit.
• "Key Registration (Barcode No.)": When the ignition key is
replaced by the full service key set, the handle lock service
key set, immobi and keyless key assembly or immobilizer
key assembly is replaced by the piece.
• "Keyless ID Reg.": When the ignition key is replaced or
added as a single unit and the immobi and keyless key
assembly.
• "Tire Pressure Sensor ID Registration": When the TPMS
transmitter is replaced and/or the WCM is replaced.
• "Tire Pressure Sensor Check": When the tire pressure sen-
sor data is checked.
• "Tire Pressure Sensor ID Check": When the tire pressure
sensor ID is checked.
NOTE: For "ENG Key Code & VIN Reg," refer to GROUP
00
−
Precautions before Service
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
System Select
Select Model Year and System
System List
Model Year
Vehicle Information
Loading Option Setup
OPC
With Option
Option Name
IMMOBI & Keyless & TPMS
VF2
VF3
IMMOBI & F.A.S.T. & TPMS
Model Name
Model Year
Model Code
Up to 2005 MY
From to 2006 MY
1
2
3
4
5
6
7
8
9
10
MPI/GDI/Diesel
F.A.S.T./IMMO/Keyless/TPMS
AT/CVT/A-MT
ABS/ASC/ASTC
SAS
Multi Select 4WD
SRS Airbag
A/C
ETACS
Meter
AC609809
OK button
AB
System Select
Please select function.
Special Function
Key Registration
Key Registration (Barcode No.)
Keyless ID Reg.
ENG key code & VIN Reg.
F.A.S.T./IMMO/Keyless/TPMS
Additional key registration
Tire Pressure Sensor ID Check
Tire Pressure Sensor ID Registration
Tire Pressure Sensor Check
AC709283
AB
Option: When IMMOBI & Keyless & TPMS is selected
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-119
5. After operation check, turn the ignition switch to the "LOCK"
(OFF) position.
6. Remove the scan tool MB991958.
.
"KEY REGISTRATION"/"ADDITIONAL KEY
REGISTRATION" METHOD
1. When "Key registration" or "Additional key registration"
screen is displayed, enter the password for the key
registration and press the OK button. Then, "Executing!" is
displayed and the registration process starts.
NOTE:
.
•
If the wrong password is entered consecutively 5 times,
the password entry for the key registration will be dis-
abled for 16 minutes.
•
The key registration cannot be cancelled during the
operation.
2. When the key registration is completed, "Completed" is
displayed. To register the next key, follow the message on
the screen and press the OK button. Then, "Executing!" is
displayed again and the registration process for the next key
starts. To finish the key registration, press the cancel button.
NOTE:
.
•
In order to register another key consecutively after regis-
tering the first key, the ignition switch must be turned to
the ON position with the second key within 30 seconds
after turning it to the "LOCK" (OFF) position with the first
key.
•
Up to eight keys can be registered.
•
When the key cannot be registered using scan tool
MB991958, refer to Inspection Procedure 2 "The ignition
key cannot be registered using scan tool
.
.
"KEY REGISTRATION (BARCODE NO.)" METHOD
1. When "Key Registration (Barcode No.)" screen is displayed,
enter the password for the key registration and press the OK
button.
NOTE: If the wrong password is entered consecutively 5
times, the password entry for the key registration will be dis-
abled for 16 minutes.
Special Function
Keyless ID Registration
F.A.S.T./IMMO/Keyless/ TPMS
AC610088
AB
OK button
AC509787
AB
Cancel button
Special Function
Key Registration (Barcode No.)
F.A.S.T./IMMO/Keyless/ TPMS
AC610089
AB
OK button
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-120
2. Follow the message on the screen to enter the bar code No.,
and then press the OK button.
3. When "Do you want to start registration?" is displayed, press
the OK button to start the registration, or press the Cancel
button to cancel the registration.
4. "Key Registration was completed" is displayed. Press the
OK button to finish the registration.
NOTE: When the key cannot be registered using scan tool
MB991958, refer to Inspection Procedure 2 "The ignition key
cannot be registered using scan tool
.
"KEYLESS ID REG." METHOD
1. On the "Keyless ID Reg." screen, enter the password and
press the OK button.
2. Register within 1 minute and send the programming packet
*
to register the keyless ID. To register multiple keys, register
the next key within 1 minute from the registration operation
of previous key. Complete the registration of necessary
keys, then press the OK button to finish the keyless ID
registration.
NOTE:
.
•
Up to eight ignition keys can be registered.
•
*
: Programming packet sending procedure
Complete the following steps 1 to 3 within four seconds.
1. Press and hold both the lock and the unlock switch
for 1 second or longer.
2. Release both the lock and the unlock switch for 0.5
second or longer.
3. Press the unlock switch.
3. Push the OK button after "Keyless ID Registration was
finished." is displayed.
Special Function
Key Registration (Barcode No.)
F.A.S.T./IMMO/Keyless/ TPMS
AC709688
AC502858
AC
Barcode
Special Function
Keyless ID Registration
F.A.S.T./IMMO/Keyless/ TPMS
AC610066
AB
OK button
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст