Mitsubishi Evolution X. Manual — part 624
DIAGNOSIS
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-113
STEP 3. Register the keyless ID using a known-good
transmitter of the same type again, and check the trouble
symptom.
(1) Register a known-good transmitter of the same type.
(2) Check if the signals from the transmitter switches are
received.
Q: Can the transmitter be registered correctly?
YES : Replace the original transmitter with a new one.
NO : Replace the WCM (Including when the new
transmitter cannot be registered). Replace WCM and
register the ID codes (Refer to
transmitter works normally, the input signal from the
transmitter should be normal.
CHECK AT ECU TERMINALS
M1427500900120
AC507349
C-07
AH
Terminal
No.
Check item
Check condition
Normal condition
1
Receiver antenna assembly
CLOCK output
Ignition key lock button, unlock
button, and trunk lid button: ON
0 to 5 V (pulse signal)
2
−
−
−
3
Receiver antenna assembly DATA
output
Ignition key lock button, unlock
button, and trunk lid button: ON
0 to 5 V (pulse signal)
4
−
−
−
5
Receiver antenna assembly power
control
Ignition switch: OFF
0 to 5 V (pulse signal)
6
Power supply (Battery)
Always
Battery voltage
7
Ground
Always
0 V
8
Receiver antenna assembly ground Always
0 V
9
Power supply (Ignition switch: IG1) Ignition switch: ON
Battery voltage
10
CAN L
−
−
11
CAN H
−
−
12
Receiver antenna assembly power
supply
Always
5 V
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-114
ON-VEHICLE SERVICE
ID CODES REGISTRATION PROCEDURE
M1427506300234
REGISTRATION USING SCAN TOOL MB991958
(M.U.T.-III SUB ASSEMBLY)
Required Special Tools:
• MB991958 Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827 M.U.T.-III USB Cable
• MB991910 M.U.T.-III Main Harness A
The ID codes necessary for the engine immobilizer system, the
keyless entry system and the TPMS can be registered using
the scan tool MB991958 (M.U.T.-III sub assembly). KOS and
keyless operation key are indicated as F.A.S.T and F.A.S.T.-key
respectively in the scan tool MB991958 (M.U.T.-III sub assem-
bly) screen.
CAUTION
Do not register the ignition key registered for other vehi-
cles.
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-115
SUPPLY UNIT LIST FOR INDIVIDUAL KEY
KEY SUPPLY UNIT LIST FOR OTHER THAN INDIVIDUAL KEY
NOTE:
.
•
When re-registering the key (key ID and keyless ID), all the
keys (key ID and keyless ID) registered before must be
re-registered because all of them will be erased.
•
If the registration fails, repeat from the start.
•
After registering the keys, make sure that the engine is
started normally with all of the keys registered.
Ignition key
AC609713
Full service key set
Handle lock service key set
Door service key set
NOTE: Key (It is the key that comes with the door
service key set. It can only be used for locking
and unlocking, and it cannot start the engine.)
AC609714
AC709684
AC610062
AC607881
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-116
AC710587AB
Screen flow of scan tool MB991958 (M.U.T.-III sub assembly)
Key Registration
(Barcode No.) *1
Key
Registration *1
Key &
F.A.S.T.-key
Registration *2
OK
OK
OK
OK
OK
OK
OK
OK
Key ID input
Execution
check
Barcode No.
registration
completed
Special
Function
F.A.S.T.-key
registration
Executing
F.A.S.T.-key
registration
completed
Registration
result display
Special
Function
ENG key code
& VIN Reg. *1, *2
OK
NOTE:
*1 Show the menu displayed when the vehicles for WCM.
*2 Show the menu displayed when the vehicles for KOS.
Cancel
Password input
Additional key
registration *1
Key registration
Completion and
an addition?
Password input
Password input
Go to A
Cancel
OK
Key registration
Completion and
an addition?
Special
Function
Refer to GROUP 00
How to Perform
VIN Writing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст