Mitsubishi Evolution X. Manual — part 737
PASSENGER'S (FRONT) AIR BAG MODULE
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-395
REMOVAL SERVICE POINTS
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air
bag(s) deployment.
.
<<B>> PASSENGER'S (FRONT) AIR BAG
MODULE REMOVAL
WARNING
•
The air bag module must not be measured with
such equipment as an ohmmeter.
•
The air bag module must not be disassembled.
•
The removed air bag module should be stored in a
clean, dry place with the deployment surface fac-
ing up.
Insert a flat-tipped screwdriver or similar tool to the location
shown in the figure. After disengaging the tabs, remove the
passenger's (front) air bag module.
ACX00583
Insulating tape
Battery cable
Battery
AF
AC609682AB
Flat-tipped
screwdriver
Flat-tipped
screwdriver
Passenger's (front)
air bag module
PASSENGER'S (FRONT) AIR BAG MODULE
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-396
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
WARNING
Dispose of air bag modules only according to the
specified procedure (Refer to
).
1. When installing the new air bag modules, refer to
).
2. Connect the negative (
−) battery cable.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
3. Connect scan tool MB991958 to the data link connector.
4. Turn the ignition switch to the “ON” position.
5. Check DTCs using scan tool MB991958 to ensure entire
SRS operates properly.
At this time, check that no DTC except B1B02, B1B06,
B1B0A and B1B0E are set.
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
6. Turn the ignition switch to the "LOCK" (OFF) position.
Disconnect the negative (
−) battery cable and tape the
terminal to prevent accidental connection and air bags
deployment.
.
>>B<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to “ON” position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and go out?
4. If yes, the SRS system is functioning properly. If not, refer to
.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
AC709154
SRS warning light
AB
PASSENGER'S (FRONT) AIR BAG MODULE
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-397
INSPECTION
M1524047400059
CAUTION
• Never measure circuit resistance in the air bag modules
(squib) even with the specified tester. Measuring the
circuit resistance with a tester causes accidental air
bag deployment due to current that flows or static,
resulting in serious personal injury.
• When replacing the parts, discard the old parts after
deploying the air bag according to the specified proce-
dure (Refer to
).
If any malfunction is found in the following inspections, replace
the air bag module with a new one.
1. Check the harness and connector for damage and the ter-
minal for deformation.
2. Check the air bag inflator cases for dents, cracks or defor-
mation.
3. Check the air bag module for proper installation.
AC608598
Squib connectors
Inflator
AB
KNEE AIR BAG MODULE
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-398
KNEE AIR BAG MODULE
REMOVAL AND INSTALLATION
M1524044000074
WARNING
•
Never attempt to disassemble or repair the knee air bag modules. If faulty, replace it.
•
Do not drop the knee air bag modules or allow contact with water, grease or oil. Replace it
if a dent, crack, deformation or rust is detected.
•
Do not expose the knee air bag modules to temperatures over 93
°
C (200
°
F).
•
After deployment of the air bag, replace the air bag module with a new one.
•
Wear gloves and safety glasses when handling air bags that have already deployed.
•
An undeployed knee air bag module should only be disposed of in accordance with the
procedures (Refer to
).
•
When removing and installing the front passenger seat, be sure to carry out accuracy
check occupant classification sensor after the seat has been installed in the vehicle
(On-vehicle Service
).
Pre-removal Operation
• Turn the ignition switch to the "LOCK" (OFF) position.
AC609125
1
2
9.5 ± 3.5 N·m
84 ± 31 in-lb
AB
Steering column
Removal steps
<<
A
>>
1. Negative (
−) battery cable
• Instrument panel cover assembly
(Refer to GROUP 52A, Instrument
Lower Panel
<<
B
>>
2. Knee air bag module
Installation steps
>>
A
<< • Pre-installation inspection
>>
B
<< 2. Knee air bag module
• Instrument panel cover assembly
(Refer to GROUP 52A, Instrument
Lower Panel
1. Negative (
−) battery cable
>>
C
<< • Post-installation inspection
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст