Mitsubishi Evolution X. Manual — part 1133
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-167
STEP 14. Check the wiring harness between joint
connector (CAN1) C-105 and KOS-ECU connector C-05 for
a short to power supply. Measure the voltage at joint
connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between joint connector (CAN1)
terminal 9 and body ground.
OK: 4.7 volts or less
(4) Measure the voltage between joint connector (CAN1)
terminal 22 and body ground.
OK: 4.7 volts or less
Q: Do all the voltages measure 4.7 volts or less?
YES : Go to Step 16.
NO : Go to Step 25.
STEP 15. Check the wiring harness between joint
connector (CAN1) C-105 and WCM connector C-07 for a
short to power supply. Measure the voltage at joint
connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
AC608178
TEST
HARNESS
Harness side: C-105
BJ
AC608178
Harness side: C-105
BK
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-168
(3) Measure the voltage between joint connector (CAN1)
terminal 7 and body ground.
OK: 4.7 volts or less
(4) Measure the voltage between joint connector (CAN1)
terminal 20 and body ground.
OK: 4.7 volts or less
Q: Do all the voltages measure 4.7 volts or less?
YES : Go to Step 16.
NO : Go to Step 26.
STEP 16. Check the wiring harness between joint
connector (CAN1) C-105 and SRS-ECU connector C-37 for
a short to power supply. Measure the voltage at joint
connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between joint connector (CAN1)
terminal 8 and body ground.
OK: 4.7 volts or less
AC608178
TEST
HARNESS
Harness side: C-105
BL
AC608178
Harness side: C-105
BM
TEST
HARNESS
AC608178
TEST
HARNESS
Harness side: C-105
BN
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-169
(4) Measure the voltage between joint connector (CAN1)
terminal 21 and body ground.
OK: 4.7 volts or less
Q: Do all the voltages measure 4.7 volts or less?
YES : Go to Step 17.
NO : Go to Step 27.
STEP 17. Check the wiring harness between joint
connector (CAN1) C-105 and occupant classification-ECU
connector D-39-2 for a short to power supply. Measure the
voltage at joint connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between joint connector (CAN1)
terminal 11 and body ground.
OK: 4.7 volts or less
(4) Measure the voltage between joint connector (CAN1)
terminal 24 and body ground.
OK: 4.7 volts or less
Q: Do all the voltages measure 4.7 volts or less?
YES (vehicles without hands free system) : Go to Step
19.
YES (vehicles with hands free system) : Go to Step 18.
NO : Go to Step 28.
AC608178
Harness side: C-105
BO
TEST
HARNESS
AC608178
TEST
HARNESS
Harness side: C-105
BP
AC608178
Harness side: C-105
BQ
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-170
STEP 18. Check the wiring harness between joint
connector (CAN1) C-105 and hands free module connector
C-11 for a short to power supply. Measure the voltage at
joint connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between joint connector (CAN1)
terminal 10 and body ground.
OK: 4.7 volts or less
(4) Measure the voltage between joint connector (CAN1)
terminal 23 and body ground.
OK: 4.7 volts or less
Q: Do all the voltages measure 4.7 volts or less?
YES : Go to Step 19.
NO : Go to Step 29.
STEP 19. Check the wiring harness between joint
connector (CAN1) C-105 and A/C-ECU connector C-22 for a
short to power supply. Measure the voltage at joint
connector (CAN1) C-105.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (CAN1), and measure the
voltage at the wiring harness side of joint connector
(CAN1).
(2) Turn the ignition switch to the ON position.
AC608178
TEST
HARNESS
Harness side: C-105
BR
AC608178
Harness side: C-105
BS
TEST
HARNESS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст