Mitsubishi Evolution X. Manual — part 849
DOOR MIRROR
TSB Revision
EXTERIOR
51-79
CAUTION
When attaching the marks, the ambient temperature
should be 20
− 38° C (68 − 100° F) and the air should be
completely free of dust. If the ambient temperature is lower
than 20
° C (60° F), the marks and the places on the vehicle
body where the marks are to be attached should be heated
to 20
− 30° C (68 − 86° F).
(2) Peel off the protection sheet on the back of the marks to
affix it in position.
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400933
AC607955
AC607955
3
AB
A
Section A – A
Power window
switch panel
: Claw positions
A
A
4
1
2
5.0 ± 2.0 N·m
45 ± 17 in-lb
AC705416
3
AD
3
Claw
B
Section B – B
Door mirror outer cover claw positions
: Claw positions
B
B
B
Claw
B
B
DOOR MIRROR
TSB Revision
EXTERIOR
51-80
REMOVAL SERVICE POINT
.
<<A>> DOOR MIRROR OUTER COVER REMOVAL
CAUTION
The claws of the mirror are prone to break when working in
cold temperatures. Always use a hair drier or the like to
warm up the mirror claws and its periphery to 20
° C or
higher prior to works. When the mirror is heated too
quickly from its cold state, it may be broken.
1. Slant the mirror upward with your hands. Then insert a
flat-tipped screwdriver wrapped with protective tape
between the pivot plate and mirror through the cut-out from
behind the mirror. Now pry off the mirror claws and release
the lower side of the mirror as shown in the illustration.
2. Release the upper side of the mirror from the tabs while
pulling out the mirror downwards.
Door mirror assembly removal
steps
•
Tweeter (Refer to GROUP 54A,
Speaker
)
•
Door mirror connector connection
1.
Door mirror assembly
Door mirror outer cover removal
steps
2.
Mirror
<<A>>
>>A<<
3.
Door mirror outer cover
Remote controlled mirror switch
removal steps
•
Front door trim (Refer to GROUP
52A, Door Trim
4.
Remote controlled mirror switch
AC605127
A
A
AC
Section A – A
Claw positions
Claws
Claw
Claw
Pivot plate
Mirror
Mirror
Flat-tipped screwdriver
Flat-tipped screwdriver
Flat-tipped screwdriver
Protective tape
DOOR MIRROR
TSB Revision
EXTERIOR
51-81
3. Remove the door mirror outer cover by disengaging the
claws in the numerical order of the illustration from the mirror
body side.
INSTALLATION SERVICE POINT
.
>>A<< DOOR MIRROR OUTER COVER INSTAL-
LATION
CAUTION
Tap the claw positions securely to confirm that they are
engaged securely.
Install the door mirror outer cover by engaging the claws in the
numerical order of the illustration.
INSPECTION
M1511006500554
REMOTE CONTROLLED MIRROR OPERATION
CHECK
Check that the mirror moves as described in the table when
each terminal is connected to the battery.
AC608686AB
2
1
2
: Claw positions
2
1
AC608686AC
2
1
2
1
1
: Claw positions
Battery connection
Direction
operation
• Connect terminal 8 to the negative
battery terminal.
• Connect terminal 6 to the positive battery
terminal.
Up
• Connect terminal 8 to the positive battery
terminal.
• Connect terminal 6 to the negative
battery terminal.
Down
• Connect terminal 8 to the negative
battery terminal.
• Connect terminal 7 to the positive battery
terminal.
Right
AC608725AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-82
DOOR MIRROR CONTROL SWITCH CONTINUITY
CHECK
• Connect terminal 8 to the positive battery
terminal.
• Connect terminal 7 to the negative
battery terminal.
Left
Battery connection
Direction
operation
Switch
position
Tester connection
Specified
condition
OFF
9
− 2, 9 − 3, 9 − 6, 9 − 10,
9
− 11, 1 − 2,1 − 3, 1 − 6,
1
−10, 1 − 11
Open circuit
Left
side
OFF
9
− 6, 9 − 10, 9 − 11,
1
− 6, 1 − 10, 1 − 11
Open circuit
Up
1
− 6, 9 − 11
Continuity
exists (2
Ω or
less)
Down 1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right
side
OFF
9
− 2, 9 − 3, 9 − 6,
1
− 2, 1 − 3, 1 − 6
Open circuit
Up
1
− 6, 3 − 9
Continuity
exists (2
Ω or
less)
Down 1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
AC406691
2
1
4
3
5
10
9
8
7
6
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст