Mitsubishi Evolution X. Manual — part 848
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-75
AC707936AB
Windshield washer
nozzle
<Left>
<Right>
Unit: mm(in)
Ceramic line terminal
15
(0.59)
445
(17.52)
445
(17.52)
15
(0.59)
105(4.13)
90(3.54)
90(3.54)
45
(1.77)
Vehicle center
line
105(4.13)
105
(4.13)
: Right side washer
: Left side washer
210(8.27)
105
(4.13)
45
(1.77)
295
(11.61)
190
(7.48)
95
(3.74)
50
(1.97)
100(3.94)
295
(11.61)
190
(7.48)
95
(3.74)
50
(1.97)
100(3.94)
480(18.89)
480(18.89)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-76
LIGHTING CONTROL SENSOR
REMOVAL AND INSTALLATION
M1511028300020
Refer to GROUP 54A
−Lighting control sensor
).
ADAPTATION
M1511028600010
CAUTION
• Before performing the adaptation, check if the lighting
control sensor (rain sensor)-related diagnostic trouble
code is set. (if set, refer to GROUP 54A, Headlight Diag-
nostic Trouble Code Chart
).
• Turn the wiper switch to the OFF position.
1. Clean the windshield in fine weather.
2. Wipe the surface of the windshield thoroughly, and check
that the surface is dry.
3. Turn the ignition switch to the ON position.
4. Turn the ignition switch to the LOCK (OFF) position.
CAUTION
Before connecting or disconnecting scan tool MB991958,
always turn the ignition switch to the LOCK (OFF) position.
5. Connect the scan tool MB991958 to the data link connector.
6. Turn the ignition switch to the ON position.
7. Wipe the windshield surface of the lighting control sensor
section thoroughly, and check that the surface is dry.
8. Select "LIN" on the "System Select" screen, and press the
"OK" button.
9. Select "Rain light sensor" on the "System Select" screen,
and press the "OK" button.
10.Select "Special Function" on the "Rain light sensor" screen.
11.Select "Rain Sensor Adaptation" on the "Special Function"
screen.
12.Press the "OK" button, and execute the "Rain Sensor
Adaptation."
13.Press the "OK" button after the execution screen is
displayed.
14.Press the "OK" button after "Completed" is displayed.
MARK
TSB Revision
EXTERIOR
51-77
MARK
REMOVAL AND INSTALLATION
M1511011802308
INSTALLATION SERVICE POINT
.
>>A<< MARK INSTALLATION
AC708418
1
3
2
4
N
N
N
N
AD
5
N
Removal
1.
Front three-diamond mark (Refer to
.)
>>A<<
2.
Front step plate
>>A<<
3.
Rear three-diamond mark
>>A<<
4.
MITSUBISHI mark
>>A<<
5.
LANCER EVOLUTION mark
Removal (Continued)
AC704761AB
2
2
A
A
Scuff plate
Section A - A
2. Front step plate
side sill
Body panel notch
24.0 mm
(0.94 in)
190.0 mm
(7.48 in)
MARK
TSB Revision
EXTERIOR
51-78
1. Installation position
Attach each mark to the position shown in the illustration.
2. Installation procedure
(1) Use 3M
™ AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
AC609448 AE
116.3 mm
(4.58 in)
3. Rear three-diamond mark
Center line of vehicle
Trunk lid panel
press line
High mount stop light
61.5 mm
(2.42 in)
AC609134
AE
44.7 mm
(1.76 in)
4. MITSUBISHI mark
Trunk lid panel
end line
30.5 mm
(1.20 in)
Trunk lid panel
press line
45.5 mm
(1.79 in)
AC708779
AB
44.7 mm
(1.76 in)
5. LANCER EVOLUTION mark
Trunk lid panel
end line
30.5 mm
(1.20 in)
Trunk lid panel
press line
45.7 mm
(1.80 in)
6.0 mm
(0.24 in)
4.0 mm
(0.16 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст