Mitsubishi Evolution X. Manual — part 968
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-233
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
scan tool (M.U.T.-III)
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 3.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 3. Using scan tool MB991958, read the combination
meter diagnostic trouble code.
(1) Check whether a combination meter-related DTC is set.
(2) Turn the ignition switch to the "ON" position.
Check whether the combination meter-related DTC is set.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Diagnose the combination meter (Refer to
combination meter, Diagnosis
NO : Go to Step 4.
STEP 4. Using scan tool MB991958, check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Perform the actuator test for the combination meter, and
check that the fog light indicator illuminates (Refer to
combination meter, Diagnosis
).
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result normal?
YES : Replace the ETACS-ECU.
NO : Replace the combination meter.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-234
ON-VEHICLE SERVICE
FRONT FOG LIGHT AIMING
M1540400300282
PRE-AIMING INSTRUCTIONS
1. Inspect for rusted or faulty front fog light assemblies.
2. These conditions must be corrected before a satisfactory
adjustment can be made.
3. Inspect tire inflation, and adjust if necessary.
4. If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [3 kg (6.5 pounds)
per gallon].
5. There should be no other load in the vehicle other than
driver or substituted weight of approximately 68 kg (150
pounds) placed in driver's position.
6. Thoroughly clean the front fog light lenses.
7. Place the vehicle on a level floor, perpendicular to a flat
screen 7.62 meters (25.0 ft) away from the bulb
center-marks on the fog light lens.
8. Rock the vehicle sideways to allow the vehicle to assume its
normal position.
9. Bounce the front suspension through three (3) oscillations
by applying the body weight to the hood or bumper.
10.Measure the center of the front fog lights as shown in the
illustration.
11.Four lines of adhesive tape (or equivalent markings) are
required on screen or wall:
(1) Position a vertical tape or mark so that it is aligned with
the vehicle center line.
(2) Measure the distance from the center of the front fog light
lens to the floor. Transfer the measurement to the screen.
Horizontal tape or mark on the screen is for reference of
vertical adjustment.
(3) Measure the distance from the center line of the vehicle
to the center of each front fog light. Transfer the
measurement to the screen. Vertical tape or mark on the
screen is for reference to the center line of each front fog
light.
AC706274
AC
Front fog light
center
AC307983AD
(1)
(2)
(3)
Front fog light center
Vehicle center line
(3)
7.62 m (25.0 ft)
Screen
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-235
FOG LIGHT ADJUSTMENT
1. Check if the beam shining onto the screen is at the standard
value.
Standard value:
(Cutoff line direction): The horizontal line 153.0 mm
(6.02 inches) (1.15 degrees angle) below the hori-
zontal line (H)
Limit:
(Vertical direction): Area from 53.2 mm (2.09 inches)
(0.4 degrees angle) above the cutoff line to 99.8
mm (3.93 inches) (0.75 degrees angle) below the
cutoff line
(Horizontal direction): Vertical line (V)
± 599.7 mm (±
23.6 inches) (
± 4.5 degrees angle)
2. If it is not within the standard value range, adjust by turning
the adjusting screw.
NOTE: The horizontal direction is non-adjustable. If deviation of
the light beam axis exceeds the standard value, check that the
mounting location or some other points are not faulty.
FRONT FOG LIGHT BULB REPLACEMENT
M1540400400289
CAUTION
Don't touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty, clean it
with alcohol or thinner immediately and dry well, and then
install it.
1. Remove the assembling clip of engine room under cover
front A shown in the figure, and turn up the engine room
under cover front A.
AC407086
Cutoff line
(H)
(V)
Hot zone
mm (in)
53.2 (2.09)
99.8 (3.93)
153.0
(6.02)
599.7 (23.6) 599.7 (23.6)
AC
AC706275
Phillips screwdriver
(Vertical direction adjustment)
AC
AC706695AC
Engine room under cover front A
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-236
2. Disconnect the connector and withdraw the bulb.
REMOVAL AND INSTALLATION
M1540400500123
AC609657
AB
Front fog light bulb
Post-installation operation
Check the beam direction of the front fog light (Refer to Front
Fog light Aiming
AC706707AC
1
2
4
5
3
1.2 ± 0.7 N·m
11 ± 6 in-lb
Removal steps
1.
Front bumper and radiator grille
assembly (Refer to GROUP 51
−
Front Bumper Assembly and
Radiator Grille
)
2.
Front fog light bracket
3.
Fog light assembly
4.
Bulb
5.
Fog light unit
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст