Mitsubishi Evolution X. Manual — part 969
SIDE TURN-SIGNAL LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-237
INSPECTION
FRONT FOG LIGHT RELAY CHECK
M1540400700105
SIDE TURN-SIGNAL LIGHT
REMOVAL AND INSTALLATION
M1541800200286
Battery voltage
Terminal number Normal
conditions
Not energized
3
− 4
No
continuity
With current supply
[terminal 1 (+), terminal 2 (
−)]
Continuity
exists
(2 ohms or
less)
AC708971
2
3
4
1
AF
Front fog light relay
AC609819
1
AB
Removal step
<<
A
>>
>>
A
<<
1.
Side turn-signal light assembly
SIDE TURN-SIGNAL LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-238
REMOVAL SERVICE POINT
.
<<A>> SIDE TURN-SIGNAL LIGHT REMOVAL
Push the side turn-signal light toward the vehicle rear to bend
the hook, and then remove by disengaging the tab from the
fender panel.
INSTALLATION SERVICE POINT
.
>>A<< SIDE TURN-SIGNAL LIGHT INSTALLATION
Engage the claw to the fender panel to install the side turn sig-
nal light.
AC506856
Side turn-signal light
AC
Push
Forward of vehicle
AC506857
Hook
Claw
Fender
panel
AC
Forward of vehicle
DOME LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-239
DOME LIGHT
GENERAL INFORMATION
M1542000100435
• A front dome light, installed to the front part of the
roof, has been equipped with the lens-push type
front dome light / reading light which can be oper-
ated easily from the driver's and front passen-
ger's seat, offering excellent operability for
turning on and off the light.
• The rear dome light, which illuminates the rear
passenger's seat, is installed above the rear seat.
<Vehicle without sunroof>
• The luggage compartment light is installed to the
upper part of the luggage compartment.
AC709153
AB
Rear dome light
Front dome light
(Front dome light / reading lights)
Luggage compartment light
DOME LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-240
SPECIAL TOOLS
M1541301600088
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III
sub-assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles
without CAN
communication
system)
e. M.U.T.-III main
harness C (for
Daimler
Chrysler
models only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G:
MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
DTC, data list and actuator test
check.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст