Mitsubishi Evolution X. Manual — part 362
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
MANUAL TRANSAXLE
22A-97
STEP 4. Scan tool service data
Check the service data below.(Refer to
• Item No.22: FL wheel speed sensor <FL>
• Item No.23: FL wheel speed sensor <FR>
• Item No.24: FL wheel speed sensor <RL>
• Item No.25: FL wheel speed sensor <RR>
Q: Is the check result normal?
YES : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
NO : Go to Step 5.
STEP 5. Check whether the DTC is reset.
Q: Is DTC No. U1427 set?
YES : Replace the AWC-ECU.(Refer to
.) Then
go to Step 6.
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
STEP 6. Check whether the DTC is reset.
Q: Is DTC No. U1415 set?
YES : Return to Step 1.
NO : This diagnosis is complete.
DTC U1428: G and Yaw Rate Sensor Data Error
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect diagnostic trouble code may be
set. Prior to this diagnosis, diagnose the CAN
bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
• Do not drop the G and yaw rate sensor or sub-
ject it to a shock.
• When G and yaw rate sensor is replaced, cali-
brate G and yaw rate sensor (refer to GROUP
35C
− On-vehicle Service
), and ini-
tialize the lateral/longitudinal acceleration
correction amount stored in AWC-ECU. (Refer
to item No.10: Lateral acceleration correction
amount initialization, and No. 11: Longitudinal
acceleration correction amount initialization
.)
.
OPERATION
AWC-ECU communicates with the G and yaw rate
sensor via the CAN bus lines.
.
DTC SET CONDITIONS
The code is set when abnormality is detected in the
signal received from the G and yaw rate sensor.
.
PROBABLE CAUSES
• Malfunction of the CAN bus line (local)
• Malfunction of G and yaw rate sensor
• Malfunction of AWC-ECU
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
MANUAL TRANSAXLE
22A-98
DIAGNOSTIC PROCEDURE
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.)
STEP 2. Scan tool diagnostic trouble code
Check if the AWC diagnostic trouble code No. U1003 is
set.(Refer to
.)
Q: Is the DTC set?
YES : Perform the relevant troubleshooting.
NO : Go to Step 3.
STEP 3. Scan tool diagnostic trouble code
Check if the AWC diagnostic trouble code No. C123C, C1242,
C2114, C2115, or C2204 is set.(Refer to
.)
Q: Is the DTC set?
YES : Perform the relevant troubleshooting.
NO : Go to Step 4.
STEP 4. Scan tool service data
Check the service data below.(Refer to
• Item No. 26: Yaw rate sensor
• Item No. 29: Lateral G sensor
• Item No. 31: Longitudinal G sensor
Q: Is the check result normal?
YES : Go to Step 5.
NO : Replace the G and yaw rate sensor. (Refer to
GROUP 35C
Then go to Step 6.
STEP 5. Check whether the DTC is reset.
Q: Is DTC No. U0428 set?
YES : Replace the AWC-ECU.(Refer to
.) Then
go to Step 6.
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
STEP 6. Check whether the DTC is reset.
Q: Is DTC No. U0428 set?
YES : Return to Step 1.
NO : This diagnosis is complete.
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
MANUAL TRANSAXLE
22A-99
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Communication between the scan tool and AWC-ECU cannot be
established
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect trouble symptom may occur.
Prior to this diagnosis, always diagnose the
CAN bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
.
COMMENTS ON TROUBLE SYMPTOM
CAN bus line, AWC-ECU power supply circuit, or
AWC-ECU may have a problem.
.
PROBABLE CAUSES
• Wrong M.U.T.-III wiring harness
• The CAN bus line is defective.
• AWC-ECU power supply circuit malfunction
• Malfunction of AWC-ECU
• ECU malfunction of other system
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Check/repair the AWC-ECU power supply
circuit.(Refer to
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.)
INSPECTION PROCEDURE 2: Mode does not change even when the AWC switch is pressed <Vehicles
with steering wheel audio remote control switch>
.
AWC MODE SELECT SWITCH SYSTEM
CIRCUIT
Refer to
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect trouble symptom may occur.
Prior to this diagnosis, always diagnose the
CAN bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
.
COMMENTS ON TROUBLE SYMPTOM
AWC switch or AWC-ECU may have a problem.
.
PROBABLE CAUSES
• AWC switch malfunction
• Malfunction of the ETACS-ECU
• Malfunction of the combination meter
• Damaged harness wires and connectors
• Malfunction of AWC-ECU
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
MANUAL TRANSAXLE
22A-100
DIAGNOSTIC PROCEDURE
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.) After repairing the CAN
bus line, go to Step 2.
STEP 2. Retest the system.
Q: Is the check result normal?
YES : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
NO : Go to Step 3.
STEP 3. Scan tool service data
Item No. 89: AWC switch (Refer to service data reference table
.)
Q: Is the check result normal?
YES : Go to Step 11.
NO : Go to Step 4.
STEP 4. AWC switch single unit check
Check the AWC switch.(Refer to
Q: Is the check result normal?
YES : Go to Step 5.
NO : Replace the AWC switch.(Refer to
.) Then
go to Step 13.
STEP 5. Measure the voltage at C-120 AWC switch
connector.
(1) Disconnect the connector, and measure the voltage
between terminal No.2 and ground at the harness side.
(2) Turn the ignition switch to the "ON" position.
OK: Battery positive voltage
Q: Is the check result normal?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. AWC switch connector, ETACS-ECU connector
check: C-120, C-317
Q: Is the check result normal?
YES : Go to Step 7.
NO : Repair the defective connector. Then go to Step 13.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст