Mitsubishi Evolution X. Manual — part 884
PROPELLER SHAFT
TSB Revision
PROPELLER SHAFT
25-11
DISASSEMBLY SERVICE POINTS
.
<<A>> COMPANION FLANGE REMOVAL
AC211610 AC
Mating marks
Make mating marks on the companion flange and center pro-
peller shaft, and then remove the companion flange.
.
<<B>>CENTER BEARING ASSEMBLY REMOVAL
AC101273
MD998801
AD
Center bearing
assembly
Use special tool MD998801 to remove the center bearing
assembly from the center propeller shaft.
.
<<C>> BOLT REMOVAL
Make mating marks on the rear propeller shaft, LJ assembly
and companion flange, and then remove the bolt.
.
<<D>>LJ ASSEMBLY REMOVAL
AC101274
LJ assembly
LJ boot
AE
1. Remove the LJ boot from the LJ assembly.
AC708561AC
Outer race
Ball
Cage
Inner
race
2. Make mating marks on the outer race, cage and inner race,
and then remove the outer race and ball.
NOTE: Note the positions of the balls so that they can be
reinstalled in their original positions.
AC101276
Inner race
Puller
Cage
AC
PROPELLER SHAFT
TSB Revision
PROPELLER SHAFT
25-12
3. Remove the inner race with cage from the rear propeller
shaft assembly by using a puller (commercially available).
4. Wipe off the grease and clean the outer race, inner race,
cage and balls.
AC708562AC
LJ assembly
Puller
5. If it is not possible to disassemble the outer race of LJ
assembly, remove the LJ assembly from the rear propeller
shaft assembly by using a puller (commercially available).
.
<<E>> LJ BOOT REMOVAL
When the LJ boot is reused, tape the spline part on the rear
propeller shaft and then remove the LJ boot.
ASSEMBLY SERVICE POINTS
.
>>A<< LJ BOOT INSTALLATION
1. Install the boot band.
2. Wrap a plastic tape around the spline part on the rear
propeller shaft and then install the LJ boot.
.
>>B<< LJ ASSEMBLY INSTALLATION
AC708563 AC
Outer race
Cage
Inner
race
1. Apply a thin coat of the specified grease to the ball grooves
of the inner and outer races.
Specified grease: Repair kit grease
2. Assemble the LJ assembly outer race, cage, balls, and inner
race with their mating marks aligned.
AC101278 AC
PROPELLER SHAFT
TSB Revision
PROPELLER SHAFT
25-13
3. Apply specified grease to the LJ assembly.
Specified grease: Repair kit grease
Amount to use: 75
± 5 g (2.6 ± 0.1 ounces)
AC101279AE
Rubber packing
LJ assembly
4. Apply a little of the specified sealant to the surface which
has groove (for packing) of LJ assembly (shown by arrows
in the illustration), fix the rubber packing.
Specified sealant: 3M
™ AAD Part No. 8730, 8731 or
equivalent
5. Set the groove side of LJ assembly (for packing) toward the
LJ boot side and install them.
AC101280 AC
Socket wrench
6. Align the mating marks of LJ assembly and rear propeller
shaft, then install the LJ assembly to rear propeller shaft
using socket wrench.
AC101281AE
Bolt
LJ boot
7. Using the bolt, align the bolt holes of the LJ boot and the LJ
assembly and install LJ boot to the LJ assembly.
8. Install the rubber packing of the companion flange side in
the same manner as described in (4) above.
.
PROPELLER SHAFT
TSB Revision
PROPELLER SHAFT
25-14
>>C<< BOOT BAND INSTALLATION
CAUTION
•
AC101282 AB
Boot
Boot band mounting
Salient
Tighten the boot part in opposite direction of convex
part for bleeding the boot.
• If there is grease in the convex part, wipe out the
grease in order to bleed the boot.
.
>>D<< CENTER BEARING
ASSEMBLY/COMPANION FLANGE/SELF
LOCKING NUT INSTALLATION
AC101283 AD
Companion flange
Self locking
nut
Center bearing
assembly
1. Install the center bearing assembly to the center propeller
shaft in the direction shown in the illustration.
2. After aligning the mating marks of the companion flange and
center propeller shaft, install them.
3. Tightening the self locking nut, press fit the center bearing
assembly using companion flange.
.
>>E<< CENTER BEARING
ASSEMBLY/COMPANION FLANGE/SELF
LOCKING NUT INSTALLATION
AC101284 AE
Rubber
mount
Dust seal
Companion
flange
Self
locking
nut
1. Install the center bearing assembly to the center propeller
shaft in the direction shown in the illustration.
2. After aligning the mating marks of the companion flange and
center propeller shaft, install them.
3. Tightening the self locking nut, press fit the center bearing
assembly using companion flange.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст