Mitsubishi Evolution X. Manual — part 552
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-115
STEP 4. Check the wiring harness between the unlock
sensor (front door: LH) connector E-18 (terminal Nos. 4, 2)
and the ground for short circuit.
(1) Disconnect unlock sensor (front door: LH) connector E-18,
and check the wiring harness.
(2) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No. 4) and ground
OK: No continuity
(3) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No. 2) and ground
OK: No continuity
Q: Is the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal Nos. 4, 2) and the
ground in good condition?
YES : Go to Step 5.
NO [unlock sensor (front door: LH) connector E-18
terminal No.4
− ground.] : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.4) and ground.
NO [unlock sensor (front door: LH) connector E-18
terminal No.2
− ground.] : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.2) and the ground.
AC709707IR
Harness side: E-18
AC709707IS
Harness side: E-18
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-116
STEP 5. Check the wiring harness between the KOS-ECU
connector C-05 (terminal Nos. 25, 36) and unlock sensor
(front door: RH) connector E-05 (terminal Nos. 4, 2) for
open circuit.
(1) Disconnect KOS-ECU connector C-05 and unlock sensor
(front door: RH) connector E-05, and check the wiring
harness.
(2) Check the wiring harness between KOS-ECU connector
C-05 (terminal No.25) and unlock sensor (front door: RH)
connector E-05 (terminal No.4).
OK: Continuity exists (2
Ω or less)
(3) Check the wiring harness between KOS-ECU connector
C-05 (terminal No.36) and unlock sensor (front door: RH)
connector E-05 (terminal No.2).
OK: Continuity exists (2
Ω or less)
Q: Is the wiring harness between KOS-ECU connector C-05
(terminal Nos. 25, 36) and unlock sensor (front door:
RH) connector E-05 (terminal Nos. 4, 2) in good
condition?
YES : Go to Step 6.
NO (KOS-ECU connector C-05 terminal No.25
− unlock
sensor (front door: RH) connector E-05 terminal No.4.) :
Repair the wiring harness between KOS-ECU
connector C-05 (terminal No.25) and unlock sensor
(front door: RH) connector E-05 (terminal No.4).
NO (KOS-ECU connector C-05 terminal No.36
− unlock
sensor (front door: RH) connector E-05 terminal No.2.) :
Repair the wiring harness between KOS-ECU
connector C-05 (terminal No.36) and unlock sensor
(front door: RH) connector E-05 (terminal No.2).
AC709707
Harness side: C-05
GN
Harness side: E-05
AC709707GO
Harness side: C-05
Harness side: E-05
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-117
STEP 6. Check the wiring harness between the unlock
sensor (front door: RH) connector E-05 (terminal Nos. 4, 2)
and the ground for short circuit.
(1) Disconnect unlock sensor (front door: RH) connector E-05,
and check the wiring harness.
(2) Check the wiring harness between unlock sensor ((front
door: RH) connector E-05 (terminal No. 4) and ground
OK: No continuity
(3) Check the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal No. 2) and ground
OK: No continuity
Q: Is the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal Nos. 4, 2) and the
ground in good condition?
YES : Go to Step 7.
NO [unlock sensor (front door: RH) connector E-05
terminal No.4
− ground.] : Repair the wiring harness
between unlock sensor (front door: RH) connector
E-05 (terminal No.4) and ground.
NO [unlock sensor (front door: RH) connector E-05
terminal No.2
− ground.] : Repair the wiring harness
between unlock sensor ((front door: RH) connector
E-05 (terminal No.2) and the ground.
STEP 7. Replace the unlock sensor, and check whether the
diagnostic trouble code is reset.
(1) Erase the DTC.
(2) Turn the ignition switch from the LOCK (OFF) position to the
ON position.
(3) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace KOS-ECU and register the ID codes (Refer
to
NO : The procedure is complete.
AC709707IT
Harness side: E-05
AC709707IU
Harness side: E-05
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-118
DTC B2415: RA module power voltage
CAUTION
• If DTC B2415 is set, diagnose the CAN bus
lines.
• When replacing the ECU, always check that
the communication circuit is normal.
Receiver Antenna Module and KOS-ECU Circuit
KOS-ECU
IMMOBILIZER
ANTENNA
RECEIVER
RECEIVER ANTENNA
ASSEMBLY
RECEIVER ANTENNA
MODULE
JOINT
CONNECTOR (6)
AC708950AX
C-41
Connectors: C-05, C-41
C-05
AC708951CG
Connectors: C-08, C-16
C-16 (B)
C-08
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст