Mitsubishi Evolution X. Manual — part 992
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-329
.
COMMENTS ON TROUBLE SYMPTOM
If the sound is not output from one of the speakers,
the speaker, radio and CD player, communication
line from the radio and CD player to the speakers
may have a problem.
.
PROBABLE CAUSES
• The speaker may be defective
• The radio and CD player may be defective
• Damaged harness wires and connectors
AC708951BG
C-116
C-23
Connectors: C-23, C-107, C-116, C-117
C-107
C-117 (BR)
AC708950BJ
C-42
C-128
Connectors: C-42, C-101, C-128, C-129
C-129 (BR)
C-101 (B)
AC708954 AO
Connector: D-01
AC708955AK
Connector: D-24
AC608167 AB
Connectors: E-02, E-13
E-02 (B)
E-13
AC608168 AJ
Connectors: E-04, E-11
E-04 (B)
E-11
AC608170 AI
Connector: E-22
AC608169AH
Connector: E-23
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-330
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
STEP 1. ETACS-ECU coding data check.
(1) Operate the scan tool to read the ETACS-ECU option
coding information (Refer to GROUP 00, Coding Table
(2) Check that the "Speaker" is set to "6 speakers".
Q: Is the check result normal?
YES : Go to Step 2.
NO : Operate the scan tool to set the option coding
"Speaker" to "6 speakers", and check the trouble
symptom.
STEP 2. Checking with audio speaker check
Perform the audio speaker check, and check which speaker
does not output the sound (Refer to
).
NOTE: In the following procedure, check the speaker or
tweeter that is abnormal.
Q: Is the check result normal?
YES (normal for all) : The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO (Either a speaker is abnormal) : Go to Step 3.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-331
STEP 3. Check door speaker connector E-13 <front-LH>,
E-11 <front-RH>, E-23 <rear-LH> or E-22 <rear-RH>, or
tweeter connector E-02 <LH> or E-04 <RH> for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is door speaker connector E-13 <front-LH>, E-11
<front-RH>, E-23 <rear-LH> or E-22 <rear-RH>, or
tweeter connector E-02 <LH> or E-04 <RH> in good
condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s) (Refer
to GROUP 00E, Harness Connector Inspection
STEP 4. Check the speaker or tweeter.
(1) Remove the speaker or tweeter (Refer to
(2) Check that the speaker or tweeter outputs the noise when
the voltage of 5 V is applied to the speaker or tweeter
connector terminal.
Q: Does the speaker or tweeter output the noise?
YES : Go to Step 5.
NO : Replace the speaker or tweeter.
STEP 5. Check radio and CD player connector C-107 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is radio and CD player connector C-107 in good
condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component (Refer to
GROUP 00E, Harness Connector Inspection
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-332
STEP 6. Check the wiring harness between the speaker or
tweeter connector terminal and the radio and CD player
connector terminal.
• Check the communication lines for open circuit and short
circuit.
• <Front door speaker (LH)> Check the wiring harness
between front door speaker (LH) connector E-13 (terminal
1, 2) and radio and CD player connector C-107 (terminal
28, 38).
NOTE: Also check joint connector C-101 and intermediate
connector C-128 for loose, corroded, or damaged terminals,
or terminals pushed back in the connector. If joint connector
C-101 or intermediate connector C-128 is damaged, repair
or replace the connector as described in GROUP 00E, Har-
ness Connector Inspection
.
• <Front door speaker (RH)> Check the wiring harness
between front door speaker (RH) connector E-11 (terminal
1, 2) and radio and CD player connector C-107 (terminal
26, 36).
NOTE: Also check joint connector C-101 and intermediate
connector C-116 for loose, corroded, or damaged terminals,
or terminals pushed back in the connector. If joint connector
C-101 or intermediate connector C-116 is damaged, repair
or replace the connector as described in GROUP 00E, Har-
ness Connector Inspection
.
• <Rear door speaker (LH)> Check the wiring harness
between rear door speaker (LH) connector E-23 (terminal 1,
2) and radio and CD player connector C-107 (terminal 27,
37).
NOTE: Also check intermediate connectors D-24 and C-42
for loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If intermediate connector
D-24 or C-42 is damaged, repair or replace the connector
as described in GROUP 00E, Harness Connector Inspec-
tion
• <Rear door speaker (RH)> Check the wiring harness
between rear door speaker (RH) connector E-22 (terminal
1, 2) and radio and CD player connector C-107 (terminal
25, 35).
NOTE: Also check intermediate connectors C-23 and D-01
for loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If intermediate connector
C-23 or D-01 is damaged, repair or replace the connector
as described in GROUP 00E, Harness Connector Inspec-
tion
• <Tweeter (LH)> Check the wiring harness between tweeter
(LH) connector E-02 (terminal 1, 2) and radio and CD player
connector C-107 (terminal 38, 28).
NOTE: Also check joint connector C-101 and intermediate
connector C-129 for loose, corroded, or damaged terminals,
or terminals pushed back in the connector. If joint connector
C-101 or intermediate connector C-129 is damaged, repair
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст