Mitsubishi Evolution X. Manual — part 627
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-125
9. The customer-programming mode is terminated by any of
the following conditions.
• When the registration of 8 transmitters are completed
• When 1 minute has elapsed without registration after the
shift to the customer-programming mode
• when 1 minute has elapsed after previous transmitter regis-
tration
• When the engine speed is more than 200 rpm
• The EEPROM abnormality occurs [When the EEPROM
abnormality occurs during the transmitter registration,
delete all the transmitters stored (including the transmitters
used for the shift to the customer-programming mode), and
finish the customer-programming mode.]
TPMS TRANSMITTER CHECK
M1427509000027
Refer to ID codes registration procedure
TPMS TRANSMITTER ID CHECK
M1427509100024
Refer to ID codes registration procedure
KEYLESS ENTRY SYSTEM CHECK
M1427505600050
Check the keyless entry system as described below. If it does
not work, perform troubleshooting. Refer to
• Operate the transmitter to check that the doors can be
locked and unlocked.
• Operate the transmitter to check that the answerback func-
tion works in response to doors locking/unlocking.
NOTE: The hazard answerback setting can be changed
using the customization function. Confirm which setting is
activated before performing these checks. Refer to
INSPECTION OF KEYLESS ENTRY TIMER LOCK
FUNCTION
M1427505800032
Attempt to unlock the doors by using the transmitter. If the
doors are not locked within 30 seconds, carry out diagnosis.
Note that the doors will not be locked if the ignition key is
inserted within the 30-second period, or the doors are opened.
Refer to
.
NOTE: The operation time of the keyless entry timer lock func-
tion can be set using the customization function. Confirm the
operation time before performing the diagnosis. Refer to
.
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-126
CUSTOMIZATION FUNCTION
M1427504500191
By operating the ETACS system or MMCS of scan
tool MB991958, the following functions can be pro-
grammed. The programmed information is held even
when the battery is disconnected.
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Hazard answer
back
Adjustment of the
number of keyless
hazard warning light
answer back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (default)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
No function
Dome light
delay timer with
door
Adjustment of
interior light delay
shutdown time
0 sec
0 second (no delay shutdown time)
7.5 sec
7.5 seconds
15 sec
15 seconds
30 sec
30 seconds (default)
60 sec
60 seconds
120 sec
120 seconds
180 sec
180 seconds
Door unlock
mode
Door lock system
All doors unlock
All the doors are unlocked when the
driver's side door is unlocked.
Dr door unlock
Only the driver's side door is unlocked
when the driver's side door is unlocked.
(default)
Auto door
unlock by P
position
Auto door unlock by
P position function
<Vehicles with
TC-SST>
Disable
No function (default)
Always enabled
Always with function
Duration of horn
chirp
Horn sounding time
during horn answer
back
Short
0.01 second (default)
Long
0.02 second
ON-VEHICLE SERVICE
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-127
Horn chirp by
keyless
Horn chirp by
keyless entry
system <vehicles
without auto light>
Not sound horn
No horn answerback function
Lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed once.
W lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)
Horn chirp by
keyless entry
system <vehicles
with auto light>
Not sound horn
No horn answerback function
Lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed once.
Lock/auto ON
During daytime, while the lighting switch is
in the AUTO position, the horn sounds
once when the lock is pressed once.
W lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)
Timer lock timer Timer lock period
adjustment
30 sec
30 seconds (default)
60 sec
60 seconds
120 sec
120 seconds
180 sec
180 seconds
Panic alarm
switch
With/without panic
alarm function
Disable
No function
Enable
With function (default)
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
WCM
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-128
WCM
REMOVAL AND INSTALLATION
M1427500800219
CAUTION
When WCM has been replaced, all key ID codes should be registered, referring to the ID code regis-
tration necessity judgment table
.
INSTALLATION SERVICE POINT
.
>>A<< WCM INSTALLATION
Check that the top claw of WCM is fixed securely to the boss of
steering lock and the antenna is not floated on the key cylinder.
AC708360
AC706388
2
3
2
3
2
3
B
B
C
4
3
1
2
AC
A
A
C
Section A-A
Section C-C
Section B-B
NOTE: Claw position is symmetrical
Claw
Claw
Claw
2.0 ± 0.5 N·m
18 ± 4 in-lb
Removal steps
1.
Ignition key cover
2.
Steering column upper cover
3.
Steering column lower cover
>>
A
<< 4.
WCM
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст