Mitsubishi Evolution X. Manual — part 1086
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-705
STEP 9. Check the Wiring harness between horn (HIGH)
connector A-44 (terminal No. 1) and horn relay connector
A-16X (terminal No. 3).
Check the output lines for open circuit and short circuit.
Q: Is the check result normal?
YES : Go to Step 10.
NO : Repair the wiring harness between horn (HIGH)
connector A-44 and horn relay connector A-16X.
STEP 10. Check the horn (HIGH) work normally.
Connect the battery as shown, and verify that the horn sounds.
Q: Is the check result normal?
YES : Go to Step 11.
NO : Replace the horn (HIGH). go to Step 11.
STEP 11. Check horn (LOW) connector A-51 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is Horn (LOW) connector A-51 in good condition?
YES : Go to Step 12.
NO : Repair the damaged parts.
STEP 12. Check the Wiring harness between horn (LOW)
connector A-51 (terminal No. 1) and horn relay connector
A-16X (terminal No. 3).
Check the output lines for open circuit and short circuit.
Q: Is the check result normal?
YES : Go to Step 13.
NO : Repair the wiring harness between horn (LOW)
connector A-51 and horn relay connector A-16X.
STEP 13. Check the horn (LOW) work normally.
Connect the battery as shown, and verify that the horn sounds.
Q: Is the check result normal?
YES : Go to Step 14.
NO : Replace the horn (LOW). go to Step 14.
AC607630AC
AC607630AC
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-706
STEP 14.Retest the theft-alarm system.
Q: Does the theft-alarm system work normally?
YES : he trouble can be an intermittent malfunction (Refer to
GROUP 00, How to use Troubleshooting/inspection
Service Points
− How to Cope with Intermittent
Malfunction
).
NO : Replace the ETACS-ECU.
REMOVAL AND INSTALLATION
M1547001000351
Theft-alarm system component parts
• Headlight assembly (Refer to
).
).
• Door switch (Refer to GROUP 42A − Door, Door
).
• Front and rear door lock actuator (Refer to
GROUP 42A
− Door, Door Handle and Latch
).
• Trunk lid latch assembly (Refer to GROUP 42A −
Trunk Lid
• Hood latch (Refer to GROUP 42A − Hood
<RHD>).
• Key reminder switch (Refer to
• Theft-alarm indicator (Refer to GROUP 52A −
Instrument Center Panel
).
Panic alarm system component parts
• Headlight assembly (Refer to
).
).
INSPECTION
THEFT-ALARM INDICATOR CHECK
M1547001100206
1. Remove the center panel.
2. Connect the battery (+) terminal with the center panel
connector (terminal No. 15). Then, check if the theft-alarm
indicator is illuminated when the battery (
−) terminal and the
center panel connector (terminal No. 12) are connected.
3. If the theft-alarm indicator is illuminated, it is judged good.
AC609727AB
PANIC ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-707
PANIC ALARM
GENERAL INFORMATION
M1547000100140
If danger is perceived near the vehicle and if the igni-
tion switch is in the OFF position or the key has been
removed, press the panic button on the ignition key
or the keyless operation key for one second, then the
headlights flash and the horn sounds for approxi-
mately 3 minutes.
Panic alarm system operation table
Construction diagram
.
Operation of keyless operation key or transmitter
System operation
Panic button
Press once
Starts the panic alarm (headlights flash and horn
honks for abut three minutes)
Lock button, Unlock button,
Trunk button, Panic button
Press again
Stops the panic alarm in progress
AC709446
PANIC
Panic button
Panic button
<Vehicles with KOS>
<Vehicles with WCM>
Theft-alarm horn
Horn (HIGH)
Horn (LOW)
Headlight
ETACS-ECU
AB
PANIC ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-708
SPECIAL TOOLS
M1547000600242
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III
sub-assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III main
harness C (for
Daimler Chrysler
models only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
Reading diagnostic trouble code.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст