Mitsubishi Evolution X. Manual — part 975
HIGH-MOUNTED STOPLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-261
HIGH-MOUNTED STOPLIGHT
REMOVAL AND INSTALLATION
M1541700200331
LICENSE PLATE LIGHT
REMOVAL AND INSTALLATION
M1541900200294
AC706683AB
2
4.5 ± 1.5 N·m
40 ± 13 in-lb
1
Removal Steps
•
Trunk lid trim (Refer to GROUP 52A
− Trims
1.
High-mounted stoplight assembly
2.
Gasket
Removal Steps (Continued)
AC710519AB
2
4
5
6
0.7 ± 0.1 N·m
6 ± 1 in-lb
3
1
7
Removal Steps
1.
License plate light assembly
2.
Lens
3.
Gasket
4.
Body
5.
Bulb
6.
Socket
7.
Grommet
Removal Steps (Continued)
HAZARD WARNING LIGHT SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-262
HAZARD WARNING LIGHT SWITCH
SPECIAL TOOLS
M1541500100084
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III
sub-assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III main
harness C (for
Daimler Chrysler
models only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G:
MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
DTC, data list and actuator test
check.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
HAZARD WARNING LIGHT SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-263
DIAGNOSIS
STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING
M1541501400088
Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points, Troubleshooting Contents
DIAGNOSTIC FUNCTION
M1541500600034
HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)
.
Required Special Tools:
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with CAN
communication system)
.
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Check harness
b. LED harness
c. LED harness
adapter
d. Probe
General service
tool (jumper)
Continuity check and voltage
measurement at harness wire or
connector
a. For checking connector pin
contact pressure
b. For checking power supply circuit
c. For checking power supply circuit
d. For connecting a locally sourced
tester
MB992006
Extra fine probe
−
Continuity check and voltage
measurement at harness wire or
connector
Tool
Tool number and
name
Supersession
Application
MB991223
a
d
c
b
DO NOT USE
BA
MB992006
HAZARD WARNING LIGHT SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-264
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to special tool MB991824.
5. Connect special tool MB991910 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the M.U.T.-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of the
connecting sequence, making sure that the ignition switch is at
the "LOCK" (OFF) position.
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
.
Required Special Tools:
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with CAN
communication system)
.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
NOTE: If the battery voltage is low, diagnostic trouble codes will
not be set. Check the battery if scan tool MB991958 does not
display.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select "System select" from the start-up screen.
4. Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.
5. Select "ETACS" from "System List", and press the "OK"
button.
NOTE: When the "Loading Option Setup" list is displayed,
check the applicable item.
6. Select "Diagnostic Trouble Code."
7. If a DTC is set, it is shown.
8. Choose "Erase DTCs" to erase the DTC.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст