Mitsubishi Evolution X. Manual — part 867

ENGINE MOUNTING

TSB Revision

POWER PLANT MOUNT

32-5

REMOVAL SERVICE POINT

.

<<A>> ENGINE MOUNTING BRACKET REMOVAL

CAUTION

When supporting the engine and transaxle assembly by
using the garage jack, pay attention not to deform the
engine oil pan.
1. Place a garage jack against the engine oil pan with a piece

of wood in between, and support the engine and transaxle
assembly.

2. Operate the garage jack so that the engine and transaxle

assembly weight is not applied to the engine mounting
insulator, and then remove the engine mounting bracket.

INSTALLATION SERVICE POINT

.

>>A<< ENGINE MOUNTING INSULATOR STOP-
PER INSTALLATION

AC710605AB

Engine side

Engine mounting insulator

Engine mounting
insulator stopper

Install the engine mounting insulator stopper as shown in the
figure.

TRANSAXLE MOUNTING

TSB Revision

POWER PLANT MOUNT

32-6

TRANSAXLE MOUNTING

REMOVAL AND INSTALLATION

M1321001401693

Pre-removal operation
• Engine Room Under Cover Front A, B, Engine Room

Under Cover Center and Engine Room Side Cover (LH)

Removal (Refer to GROUP 51, Under Cover

P.51-16

).

• Air Cleaner Assembly Removal (Refer to GROUP 15, Air

Cleaner

P.15-10

).

• Engine Control Module (ECM) Removal (Refer to GROUP

13A, Engine Control Module (ECM)

P.13A-920

).

• Engine control harness connector bracket Removal

(Refer to GROUP 54A, Battery

P.54A-10

).

• Relay box mounting bolts Removal.

Post-installation operation
• Relay box mounting bolts Installation.

• Engine control harness connector bracket Installation

(Refer to GROUP 54A, Battery

P.54A-10

).

• Engine Control Module (ECM) Installation (Refer to

GROUP 13A, Engine Control Module (ECM)

P.13A-920

).

• Air Cleaner Assembly Installation (Refer to GROUP 15,

Air Cleaner

P.15-10

).

• Engine Room Under Cover Front A, B, Engine Room

Under Cover Center and Engine Room Side Cover (LH)

Installation (Refer to GROUP 51, Under Cover

P.51-16

).

AC709069

1

2

2

3

AB

50 ± 5 N·m
37 ± 3 ft-lb

47 ± 7 N·m
35 ± 5 ft-lb

95 ± 10 N·m
71 ± 7 ft-lb

50 ± 5 N·m
37 ± 3 ft-lb

<M/T>

<TC-SST>

50 ± 5 N·m
37 ± 3 ft-lb

50 ± 5 N·m
37 ± 3 ft-lb

2

3

2

95 ± 10 N·m
71 ± 7 ft-lb

1

47 ± 7 N·m
35 ± 5 ft-lb

Removal steps

<<

A

>>

1.

Transaxle mounting bracket

>>

A

<<

2.

Transaxle mounting insulator
stopper

3.

Transaxle mounting insulator

Removal steps (Continued)

TRANSAXLE MOUNTING

TSB Revision

POWER PLANT MOUNT

32-7

REMOVAL SERVICE POINT

.

<<A>> TRANSAXLE MOUNTING BRACKET
REMOVAL

1. Place a garage jack against the transaxle case with a piece

of wood in between, and support the engine and transaxle
assembly.

2. Operate the garage jack so that the engine and transaxle

assembly weight is not applied to the transaxle mounting
insulator, and then remove the transaxle mounting bracket.

INSTALLATION SERVICE POINT

.

>>A<< TRANSAXLE MOUNTING INSULATOR
STOPPER INSTALLATION

AC708342

AB

Transaxle side

Transaxle
mounting
insulator

Transaxle mounting
insulator stopper

Install the transaxle mounting insulator stopper as shown in the
figure.

FRONT ROLL STOPPER AND CENTERMEMBER

TSB Revision

POWER PLANT MOUNT

32-8

FRONT ROLL STOPPER AND CENTERMEMBER

REMOVAL AND INSTALLATION

M1321005800032

CAUTION

• The part indicated by the *

1

mark should be temporarily tightened, and then fully tightened with

the engine and transaxle assembly weight applied on the vehicle body.

•

Pre-removal and post-installation operation
• Engine Room Under Cover Front A, B and Engine Room

Under Cover Center Removal and Installation (Refer to

GROUP 51, Under Cover

P.51-16

).

AC710612

1

53 ± 8 N·m*
40 ± 5 ft-lb*

1

1

AC

4

3

2

71 ± 10 N·m*
52 ± 7 ft-lb*

2

2

71 ± 10 N·m*
52 ± 7 ft-lb*

2

2

50 ± 5 N·m
37 ± 3 ft-lb

28 ± 4 N·m
21 ± 2 ft-lb

Removal steps

1.

Front axle crossmember bar

2.

Centermember and front roll
stopper assembly

3.

Centermember

>>

A

<<

4.

Front roll stopper

The parts indicated by the *

2

are the bolts with friction coefficient stabilizer. In removal, ensure

there is no damage, clean dust and soiling from bearing and thread surfaces, and tighten them to
the specified torque.

Removal steps (Continued)