Mitsubishi Outlander XL. Manual — part 854
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M15102100022USA0000010000
ZC5018660000
Section B – B
Section C – C
A
B
C
5
2
5
(LH)
5
(LH)
5
(RH)
5
(RH)
8
NOTE
: Clip positions
: Claw positions
1
3
4
4
B
8
7
7
5
6
6
D
N
View D
Specified grease: Multipurpose
grease SAE J310, NLGI No. 2 or
equivalent
View A
Clip
Claw
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
8.0 ± 2.0 N·m
71 ± 18 in-lb
27 ± 3 N·m
20 ± 2 ft-lb
C
Wiper blade removal steps
1.
Wiper blade assembly
>>C<<
2.
Wiper blade
Windshield wiper motor and link
assembly removal steps
>>B<<
3.
Wiper arm and blade assembly
4.
Hood weatherstrip rear
WIPER AND WASHER
51B-49
WINDSHIELD WIPER
Windshield wiper motor and link
assembly removal steps
5.
Front deck garnish
6.
Windshield wiper link
7.
Wiper motor link plate
Windshield wiper motor and link
assembly removal steps
<<A>>
>>A<<
8.
Windshield wiper motor
Required Special Tool:
⦆
MB991955: M.U.T.-III sub-assembly
⦆
MB991223: Harness set
NOTE:
For removal and installation of the wiper
and washer switch, refer to GROUP 54Ah, Column
switch P.54Ah-8.
REMOVAL SERVICE POINT
<<A>> WINDSHIELD WIPER MOTOR REMOVAL
ZC6002690001
Wiper motor
link plate
1.
Remove the wiper link rod joint from the wiper motor link plate.
51B-50
WIPER AND WASHER
WINDSHIELD WIPER
ZC600270
4
5
3
1 2
4
5
3
1 2
0000
Wiper motor
<Link plate disconnected>
<Link plate rotated>
2.
Connect the wiper motor to a battery, and rotate the link plate
as shown.
3.
In this position, withdraw the link plate from the wiper link
assembly.
INSTALLATION SERVICE POINT
>>A<< WINDSHIELD WIPER MOTOR INSTALLATION
ZC6002760000
Wiper motor link plate
1.
Position the wiper motor link plate as shown, and assemble it
to the wiper link assembly.
NOTE:
⦆
The link plate can be assembled to the wiper link assembly
only at this position. If not, rotate the link plate to this position
(Refer to Stop Position Check, P.51B-53).
⦆
Wiper motor replacement parts are supplied with the link
plate positioned as shown.
2.
Connect the assembled wiper motor to a battery, and set it to
the automatic stop position (Refer to Stop Position Check, P.
51B-53).
3.
Apply grease to the inside of link rod joint (as required) and
connect the link rod to wiper motor link plate.
WIPER AND WASHER
51B-51
WINDSHIELD WIPER
>>B<< WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
ZC6002710000
A
A
A
A
Ø2(0.08) marking
Ø2(0.08) marking
5(0.20)
5(0.20)
Ø2(0.08) marking
Section A – A
Unit: mm(in)
Front deck garnish
Install the wiper arm and blade assembly at the specified
positions.
(A): Φ 2(0.08 in) marking ± 5 mm(0.20 in)
>>C<< WIPER BLADE INSTALLATION
ZC6002720000
A
A
Wiper blade
Backing
Backing
Section A – A
Wiper
blade
Backing
Use a curved backing like that shown for the backing of a
wiper blade to ensure sustained wiper wiping performance.
51B-52
WIPER AND WASHER
WINDSHIELD WIPER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст