Mitsubishi Outlander XL. Manual — part 855
INSPECTION
M15102100023USA0000010000
WINDSHIELD WIPER MOTOR CHECK
4
5
3
1 2
4
5
3
1 2
4
5
3
1 2
ZC6002730000
Operation check
Low speed
High speed
Remove the windshield wiper motor and inspect it at the harness
connector.
WINDSHIELD WIPER MOTOR AT LOW OR HIGH SPEED
OPERATION
Connect the battery to the windshield wiper motor to inspect the
operation of motor rotation at low or high speed.
WIPER AND WASHER
51B-53
WINDSHIELD WIPER
4
5
3
1 2
4
5
3
1 2
ZC600274
4
5
3
1 2
0000
+ 5º
-10º
13º
(B) Automatic stop
(A) Low speed
Stop position check
WINDSHIELD WIPER MOTOR AT STOP POSITION
OPERATION
1.
Connect the battery to the windshield wiper motor as shown
in the illustration (A).
2.
Run the windshield wiper motor at low speed, then disconnect
the battery in the middle of the motor rotation and check to see
that the motor stops.
3.
Connect the battery to the windshield wiper motor as shown
in the illustration (B).
4.
Connect the terminals of the windshield wiper motor connector
as shown in the illustration (B).
5.
Check to see that the windshield wiper motor runs at low
speed and then stops at the automatic stop position.
WINDSHIELD WIPER SWITCH CHECK
Check the windshield wiper switch (mist, intermittent, low speed
and high speed) from the ETACS diagnosis codes for proper
operations.(Refer to GROUP 54Ad, DIAGNOSTIC TOUBLE
CODE CHART P.54Ad-8.)
51B-54
WIPER AND WASHER
WINDSHIELD WIPER
WINDSHIELD WASHER
REMOVAL AND INSTALLATION
M15102100025USA0000010000
ZC600282
1
1
2
3
4
5
A
A
0000
Section A – A
Claw
Claw
Rear washer hose
4.0 ± 2.0 N·m
36 ± 17 in-lb
10.5 ± 2.5 N·m
93 ± 22 in-lb
Windshield washer nozzle removal steps
·
Connection of windshield washer hose
1. Windshield washer nozzle
Washer hose removal steps
·
Splash shield (RH) mounting clips
·
Connection of washer nozzle/washer
motor
2. Windshield washer hose
Washer tank removal steps
·
Engine room under cover front (Refer
to P.51A-18)
·
Splash shield (RH) mounting clips
·
Connection of front/rear washer hose
3. Windshield washer tank assembly
4. Windshield washer motor
5. Windshield washer tank
WIPER AND WASHER
51B-55
WINDSHIELD WASHER
Washer motor removal steps
·
Engine room under cover front (Refer
to P.51A-18)
·
Connection of front/rear washer hose
Washer motor removal steps
4. Windshield washer motor
INSPECTION
M15102100026USA0000010000
FRONT WASHER MOTOR INSPECTION
ZC6002830000
Front washer
hose
1.
The front washer motor must be checked with the washer tank
installed and the washer fluid filled.
2.
Connect the battery to the washer motor connector as shown.
Check that the washer motor delivers washer strongly to the
front washer hose side.
WINDSHIELD WASHER FLUID EJECTION CHECK
ZC600284
600
(23.62)
49
(1.93)
49
(1.93)
461(18.15)
461(18.15)
117
(4.61)
117
(4.61)
56
(2.20)
56
(2.20)
0000
68
(2.68)
68
(2.68)
155
(6.10)
155
(6.10)
Windshield washer
nozzle
<Left>
<Right>
Vehicle center
line
Unit: mm(in)
Windshield
washer
nozzle
perpendicular
Windshield
washer
nozzle
perpendicular
Ceramic line terminal
125
(4.92)
125
(4.92)
245
(9.65)
245
(9.65)
286
(11.26)
286
(11.26)
437
(17.20)
437
(17.20)
185
(7.28)
185
(7.28)
75
(2.95)
75
(2.95)
51B-56
WIPER AND WASHER
WINDSHIELD WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст