Mitsubishi Outlander XL. Manual — part 364
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the diagnostic trouble code other than P1242 set?
YES:
Refer to, Diagnostic Trouble Code Chart P.13Ab-44.
NO:
Go to Step 2.
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1)
Turn the ignition switch to the "LOCK" (OFF) position.
(2)
After the DTC has been deleted, read the DTC again.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P1242 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
DTC P1243: Inquiry/Response Error
M11310100389USA0000010000
TECHNICAL DESCRIPTION
Monitors the computation function of the engine
control module.
DTC SET CONDITIONS
Check Condition
⦆
Ignition switch is "ON" position.
Judgment Criterion
⦆
ECM can not calculate input data.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
ECM failed.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-651
DIAGNOSTIC TROUBLE CODE PROCEDURES
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P1243 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
DTC P1244: RAM Test For All Area
M11310100390USA0000010000
TECHNICAL DESCRIPTION
Monitors the computation function of the engine
control module periodically.
DTC SET CONDITIONS
Check Condition
⦆
Ignition switch is "ON" position.
Judgment Criterion
⦆
All RAM data of ECM are defect.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
13Ab-652
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
⦆
MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P1244 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
DTC P1245: Cycle RAM Test (Engine)
M11310100391USA0000010000
TECHNICAL DESCRIPTION
Monitors the computation function of the engine
control module periodically.
DTC SET CONDITIONS
Check Condition
⦆
Ignition switch is "ON" position.
Judgment Criterion
⦆
RAM data (engine) is defect.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-653
DIAGNOSTIC TROUBLE CODE PROCEDURES
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Read the DTC.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is DTC P1245 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
DTC P1246: Communication Error
M11310100392USA0000010000
TECHNICAL DESCRIPTION
Monitors periodically whether the computation
function of the engine control module is normal.
DTC SET CONDITIONS
Check Condition
⦆
Ignition switch is "ON" position.
Judgment Criterion
⦆
ECM could not calculate input data.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
13Ab-654
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст