Mitsubishi Outlander XL. Manual — part 817
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 2. Check ETACS-ECU connector C-317 and WCM
connector C-29 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q:Is ETACS-ECU connector C-317 and WCM connector
C-29 in good condition?
YES:
Go to Step 3.
NO:
Repair the defective connector.
STEP 3. Check the wiring harness between WCM connector
C-29 (terminal No.9) and ETACS-ECU connector C-317
(terminal No.5).
⦆
Check the power supply line for open circuit.
Q:Is the wiring harness between WCM connector C-29
(terminal No. 9) and ETACS-ECU connector C-317
(terminal No. 5) in good condition?
YES:
Go to Step 4.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector.
STEP 4. Using scan tool MB991958, check data list.
Use the ETACS-ECU data list to check the signals related to the
ignition voltage.
Item No.
Item name
Normal
conditions
Item 254
IG voltage
Battery
voltage
WIRELESS CONTROL MODULE (WCM)
42C-27
DIAGNOSIS
Q:Does scan tool MB991958 display the item "IG voltage"
as normal condition?
YES:
Go to Step 5.
NO:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad,
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
DTC B2204: Coding data mismatch
M14209200019USA0000010000
DTC SET CONDITION
WCM sets the DTC B2204 when the vehicle
information data on the CAN line does not match the
vehicle information data registered in WCM.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present
when the vehicle information registered in it does not
match the vehicle information data.
TROUBLESHOOTING HINTS
⦆
Malfunction of WCM
⦆
Malfunction of ETACS-ECU
DIAGNOSTIC PROCEDURE
42C-28
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 2. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code
Check again if the DTC is set to the ETACS-ECU.
Q:Is the DTC set?
YES:
Troubleshoot the ETACS. (Refer to GROUP 54Ad,
NO:
Go to Step 3.
STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
WIRELESS CONTROL MODULE (WCM)
42C-29
DIAGNOSIS
DTC B2206: VIN mismatch
M14209200020USA0000010000
DTC SET CONDITION
WCM sets DTC B2206 when chassis number
registered in it and the VIN that has been transmitted
on the CAN bus do not match.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present
when VIN registered in it and the one that has been
transmitted on the CAN bus do not match.
TROUBLESHOOTING HINTS
⦆
Malfunction of WCM
⦆
VIN registered in engine ECU unmatched
⦆
WCM being registered to another vehicle
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check the VIN registered in engine control module.
Check if VIN registered in the engine control module matches
with the vehicle's VIN.
Q:Do VIN registered in the engine control module and the
vehicle's VIN match?
YES:
Go to Step 2.
NO:
Replace the engine control module and record VIN
(Refer to GROUP 00 - How to Perform Vehicle Identification
Number (VIN) Writing P.00-26). Record VIN and go to Step
2.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
42C-30
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст