Mitsubishi Outlander XL. Manual — part 818
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Check if the DTC is set.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The procedure is complete.
DTC B2352: Antenna fail
M14209200021USA0000010000
DTC SET CONDITION
WCM sets the DTC B2352 when open or short circuit
to the ground in the antenna is detected.
TECHNICAL DESCRIPTION (COMMENT)
When the ignition switch is turned ON, WCM transmits
signal to the antenna. When the antenna is found
faulty, WCM determines that the abnormality is
present.
TROUBLESHOOTING HINT
Malfunction of WCM (Open circuit in antenna)
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
WIRELESS CONTROL MODULE (WCM)
42C-31
DIAGNOSIS
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The procedure is complete.
DTC B2401: Keyless/KOS key ID not register
M14209200022USA0000010000
⦆
If the DTC B2401 is set, be sure to diagnose the
CAN bus line.
⦆
When replacing the ECU, always check that the
communication circuit is normal.
DTC SET CONDITION
WCM sets the DTC B2401 when no transmitter is
registered in it.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present
when the number of the transmitters registered in it is
0.
TROUBLESHOOTING HINTS
⦆
Failure of transmitter registration process
⦆
Malfunction of WCM
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
42C-32
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 2. Register the transmitter and recheck the diagnostic
trouble code.
Register the keyless entry secret code (Refer to P.42C-85.),
and recheck if the DTC is set.
(1)
Erase the DTC.
(2)
Turn the ignition switch from the "LOCK" (OFF) position to
the "ON" position.
(3)
Check if the DTC is set.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The procedure is complete.
DTC B2416: ECU internal error
M14209200023USA0000010000
DTC SET CONDITION
WCM sets DTC B2416 when it determines an
abnormal status within itself.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present, if the
data abnormality is found when the ignition switch is
turned ON and then EEPROM is written.
TROUBLESHOOTING HINTS
Malfunction of WCM
WIRELESS CONTROL MODULE (WCM)
42C-33
DIAGNOSIS
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
(5)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace WCM and register the ID codes. (Refer to P.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
DTC C1608: EEPROM Error
M14209200058USA0000010000
If there is any problem in the CAN bus lines, an incorrect
diagnostic trouble code may be set. Prior to this diagnosis,
diagnose the CAN bus lines. (Refer to GROUP 54D, Trouble
code diagnosis P.54D-17).
TPMS DTC SET CONDITION
WCM incorporates the EEPROM (nonvolatile memory). The
EEPROM stores the TPMS information. If the data in EEPROM
fails, this code is set.
TROUBLESHOOTING HINTS
The most likely causes for this DTC to set are:
⦆
Damaged wiring harness and connector
42C-34
WIRELESS CONTROL MODULE (WCM)
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст