Mitsubishi Outlander XL. Manual — part 1312

Vehicle status

Sampling timing

At vehicle moving

once every 5 seconds

At vehicle stationary

once every 1 minutes

NOTE:

Vehicle moving = vehicle speed:

approximately 25 km/h (15 mph) or more

DATA TRANSMISSION TIMING

Vehicle status

Transmission timing

At vehicle moving

once every 1 minute*

At vehicle stationary

once every 13 hours

If a sampled pressure varies by ±10 kPa
(1.5psi) from the last transmitted pressure
value, an additional transmission will occur.

NOTE:

*: Once every 15 seconds for first 30

transmission after vehicle starts moving.

WARNINGS

M24200200008USA0000010000

If the TPMS fails or the tire pressure is low, the WCM
warns the driver of that state by the TPMS warning

indicator or TPMS warning light on the multi
information display in the combination meter.

Item

State

Warning operations

Warning cancellation
conditions (Cancels
warning operations
when one of the
conditions met)

TPMS
warning light

Multi
information
display

TPMS warning light
bulb

open

circuit

check

The ignition switch is
turned

form

"LOCK" (OFF) to "ON."

The

TPMS

warning light
illuminates for
3 seconds.

-

3 seconds have passed
after the TPMS warning
light is lit.

Tire pressure alarm

The

received

tire

pressure value is under
the threshold value.

The indicator
illuminates
until it receives
the normal tire
pressure
value.

Symbol

and

"LOW

TIRE

PRESSURE" is
displayed.

The

received

tire

pressure value is over
the threshold value.

TPMS
failure
warnin
g

ID not stored The TPMS transmitter ID

is not registered in the
WCM.

Flashes*

Symbol

and

"SERVICE
REQUIRED" is
displayed.

ID

is

registered

normally.

Defective
EEPROM

Abnormality of data in the
EEPROM of the WCM is
detected.

Data in the EEPROM of
the WCM is checked to
be normal.

Problem

in

signal
reception

The signals from TPMS
transmitters cannot be
received while driving for
20 minutes or less.

The signal from the
TPMS transmitter that
was

warned

is

received.

Defective
sensor

The sensor failure signal
is received from the
TPMS transmitter.

A normal signal is
received

from

the

TPMS transmitter that
was warned.

42C-12

WIRELESS CONTROL MODULE (WCM)

SYSTEM OPERATION

Item

State

Warning operations

Warning cancellation
conditions (Cancels
warning operations
when one of the
conditions met)

TPMS
warning light

Multi
information
display

The battery
voltage of the
TMPS
transmitter is
low.

The reception problem
warning

is

activated

because of the low battery
voltage of the TPMS
transmitter.

The signal of normal
battery

voltage

is

received

from

the

TPMS transmitter that
was warned.

Vehicle
speed input
problem

The vehicle speed is not
input.

The vehicle speed is
input.

Abnormal
vehicle speed
value

The vehicle speed value
is abnormal.

The normal vehicle
speed

value

is

received.

NOTE:

*: Change to continuous illumination after

flashing for about 1 minuite.

CONFIGURATION FUNCTION

M24200200006USA0000010000

Using scan tool, the following functions can be
customized. The programmed information is held
even when the battery is disconnected.

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

Hazard answer
back

Adjustment of the
number of keyless
hazard warning light
answer

back

flashes

Lock:1, Unlock:2

LOCK: Flashes once, UNLOCK: Flashes
twice (default)

Lock:1, Unlock:0

LOCK: Flashes once, UNLOCK: No flash

Lock:0, Unlock:2

LOCK: No flash, UNLOCK: Flash twice

Lock:2, Unlock:1

LOCK: Flash twice, UNLOCK: Flash once

Lock:2, Unlock:0

LOCK: Flash twice, UNLOCK: No flash

Lock:0, Unlock:1

LOCK: No flash, UNLOCK: Flash once

Lock:0, Unlock:0

No function

Dome

light

delay timer with
door

Adjustment

of

interior light delay
shutdown time

0sec

0 second (no delay shutdown time)

7.5sec

7.5 seconds

15sec

15 seconds

30sec

30 seconds (default)

60sec

60 seconds

120sec

120 seconds

180sec

180 seconds

WIRELESS CONTROL MODULE (WCM)

42C-13

CONFIGURATION FUNCTION

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

Door

unlock

mode

Door lock system

All doors unlock

All the doors are unlocked when the driver's
side door is unlocked.

Dr door unlock

Only the driver's side door is unlocked when
the driver's side door is unlocked. (default)

Auto

door

unlock by P
position

Auto door unlock by
P position function

Disable

No function (default)

Always enabled

Always with function

P/W unlocked

With function (with power window
unlocked)

Duration of horn
chirp

Horn sounding time
during horn answer
back

Short

0.01 second (default)

Long

0.02 second

Horn chirp by
RKE

Horn chirp by RKE

Not sound horn

No horn answerback function

Lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed once.

W lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)

Timer lock timer Timer lock period

adjustment

30sec

30 seconds (default)

60sec

60 seconds

120sec

120 seconds

180sec

180 seconds

Duration

pre-

alarm

Adjustment of pre-
alarm continue time

10 sec

10 seconds (default)

6 sec

6 seconds

Alarm

With/without theft-
alarm function

Disable

No function

Enable

With function (default)

Panic

alarm

switch

With/without panic
alarm function

Disable

No function

Enable

With function (default)

42C-14

WIRELESS CONTROL MODULE (WCM)

CONFIGURATION FUNCTION

GROUP 51

EXTERIOR

CONTENTS

GENERAL INFORMATION. . . .

51-2

BUMPER. . . . . . ..

51-3

RADIATOR GRILLE. . . . .

51-4

AERO PARTS. . . . . ..

51-5

GARNISHES. . . . . ...

51-6

WINDSHIELD WIPER AND WASHER. .

51-7

REAR WIPER AND WASHER. . ..

51-11

OUTSIDE MIRROR. . . . .

51-13

CONFIGURATION FUNCTION. . .

51-13

51-1