Mitsubishi Outlander XL. Manual — part 860
ZC600374
C
C
C
C
C
A
A
A
A
B
B
B
B
2
1
2
0000
2
1
2
1
C
Section A – A
Section C – C
Section B – B
Door mirror outer cover claw positions
Claw
Claw
: Claw positions
Claw
Door mirror assembly removal
steps
·
Front door trim (Refer to GROUP 52A,
Door Trim P.52A-11)
1.
Door mirror assembly
Door mirror outer cover removal
steps
1.
Door mirror assembly
Door mirror outer cover removal
steps
<<A>>
>>A<<
2.
Door mirror outer cover
Remote controlled mirror switch
removal steps
·
Front door trim (Refer to GROUP 52A,
Door Trim P.52A-11)
3.
Remote controlled mirror switch
REMOVAL SERVICE POINTS
<<A>> DOOR MIRROR OUTER COVER REMOVAL
The tab of the mirror is prone to breakage when working in
cold temperatures. Always use a hair drier or the like to
warm up the mirror tab and its periphery to 20°C(68°F) or
higher prior to works. When the mirror is heated too quickly
from its cold state, it may be broken.
OUTSIDE MIRROR
51C-13
OUTSIDE MIRROR
ZC600375
AC302282
A
A
0000
Section A – A
Claw
Claw positions
Claws
Claw
Pivot plate
Mirror
Mirror
Minus screwdriver
Minus screwdriver
Minus screwdriver
Protective
tape
1.
Slant the mirror upward with your hands. Then insert a flat-
tipped screwdriver wrapped with protective tape between the
pivot plate and mirror through the cut-out from behind the
mirror. Now pry off the mirror tab and release the lower side
of the mirror as shown in the illustration.
2.
Release the upper side of the mirror from the tab as shown
while pulling out the mirror.
3.
Disconnect the connectors of the heated mirror.
ZC6003760000
1
2
3
1
2
3
3
: Claw positions
4.
Remove the door mirror outer cover by disengaging the claws
in the numerical order of the illustration from the mirror body
side.
51C-14
OUTSIDE MIRROR
OUTSIDE MIRROR
INSTALLATION SERVICE POINT
>>A<< DOOR MIRROR OUTER COVER INSTALLATION
Tap the claw positions securely to confirm that they are
engaged securely.
ZC6003760001
3
2
1
3
2
1
1
: Claw positions
Install the door mirror outer cover by engaging the claws in the
numerical order of the illustration.
INSPECTION
M15102200022USA0000010000
DOOR MIRROR ASSEMBLY OPERATION CHECK
Remove the door trim, and then connect the battery to the door
mirror assembly connector to check that the door mirror
operates.
ZC6003770000
Battery connection
Operation
direction
⦆
Connect terminal 5 to the negative
battery terminal.
⦆
Connect terminal 7 to the positive
battery terminal.
Up
⦆
Connect terminal 5 to the positive
battery terminal.
⦆
Connect terminal 7 to the negative
battery terminal.
Down
⦆
Connect terminal 5 to the negative
battery terminal.
⦆
Connect terminal 6 to the positive
battery terminal.
Right
⦆
Connect terminal 5 to the positive
battery terminal.
⦆
Connect terminal 6 to the negative
battery terminal.
Left
OUTSIDE MIRROR
51C-15
OUTSIDE MIRROR
REMOTE CONTROLLED MIRROR SWITCH
CONTINUITY CHECK
AC005970
ZC6003780000
Switch position
Tester
connectio
n
Specified
condition
Left side
Up
1 - 6, 9 - 11 Continuity
(Less than
2 Ω)
Down
1 - 11, 6 - 9
Right
1 - 6, 9 - 10
Left
1 - 10, 6 - 9
Right side
Up
1 - 6, 3 - 9
Down
1 - 3, 6 - 9
Right
1 - 6, 2 - 9
Left
1 - 2, 6 - 9
HEATED DOOR MIRROR CHECK
When relocating the car between locations with extremely
different temperatures (warm and cold), leave the car in the
location for a while to adapt to the temperature prior to
checking it.
ZC6003790000
Check that the resistance value between the connector
terminals is at the standard value.
Standard value: 7.2 ± 1.4 Ω at 25°C(77°F)
51C-16
OUTSIDE MIRROR
OUTSIDE MIRROR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст