Mitsubishi Outlander XL. Manual — part 1070
ZC6008720013
Connector: A-45
A-45 (B)
ZC6008710015
Connector: A-49
A-49 (B)
Connector: A-15X
A-15X
ZC6045090000
TECHNICAL DESCRIPTION (COMMENT)
If horns do not sound, the horn input signal circuit or
the ETACS-ECU may be defective. Also, the theft-
alarm function and horn may have been disabled with
a configuration function.
TROUBLESHOOTING HINTS
⦆
Horns may be defective
⦆
Horn relay may be defective
⦆
The ETACS-ECU may be defective
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB992006: Extra fine probe
⦆
MB991223: Harness set
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
ALARM SYSTEM
54Af-21
DIAGNOSIS
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
Check if DTC is set to the ETACS-ECU.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
too (M.U.T.-III) P.54Af-4."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check whether the ETACS-ECU related DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad,
NO:
Go to Step 2.
STEP 2. Using scan tool MB991958, Check the configuration
function.
(1)
Turn the ignition switch to the "ON" position.
(2)
Use the ETACS-ECU configuration function to check that the
"Alarm" is set to "Enable".
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the "Alarm" set to "Enable"?
YES:
Go to Step 3.
NO:
Use the ETACS-ECU configuration function to set the
"Alarm" to "Enable" (Refer to P.54Af-27).
STEP 3. Check which horn is defective.
Check which horn does not sound when the theft-alarm system
is triggered.
Q:Which horn does not sound?
Horn (HI) and horn (LO):
Go to Step 4.
Horn (HI) only:
Go to Step 10.
Horn (LO) only:
Go to Step 13.
STEP 4. Check horn relay connector A-15X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is horn relay connector A-15X in good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
54Af-22
ALARM SYSTEM
DIAGNOSIS
STEP 5. Check the horn relay.
Refer to P.54Af-29.
Q:Is the horn relay in good condition
YES:
Go to Step 6.
NO:
Replace the horn relay.
STEP 6. Measure the voltage at horn relay A-15X.
(1)
Remove the relay, and measure at the relay box side.
ZC5010400057
Relay box side: A-15X
(2)
Measure the voltage between horn relay connector A-15X
(terminal No. 2, 4) and the body ground.
⦆
The voltage should measure approximately 12 volts
(battery positive voltage).
Q:Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES:
Go to Step 8.
NO:
Go to Step 7.
STEP 7. Check the Wiring harness between horn relay
connector A-15X (terminal No. 2,4) and fusible link (36).
Check the power supply line for open circuit and short circuit.
Q:Is the check result normal?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Repair the wiring harness.between theft-alarm horn
relay connector A-15X and fusible link (36).
STEP 8. Check ETACS-ECU connector C-312 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connector C-312 in good condition?
YES:
Go to Step 9.
NO:
Repair the damaged parts.
STEP 9. Check the Wiring harness between horn relay
connector A-15X (terminal No. 1) and ETACS-ECU
connector C-312 (terminal No. 11).
Check the output lines for open circuit and short circuit.
Q:Is the check result normal?
YES:
Go to Step 10.
NO:
Repair the wiring harness between horn relay
connector A-15X and ETACS-ECU connector C-312.
STEP 10. Check horn (HI) connector A-49 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is horn (HI) connector A-49 in good condition?
YES:
Go to Step 11.
NO:
Repair the damaged parts.
ALARM SYSTEM
54Af-23
DIAGNOSIS
STEP 11. Check the Wiring harness between horn (HI)
connector A-49 (terminal No. 1) and horn relay connector
A-15X (terminal No. 3).
Check the output lines for open circuit and short circuit.
Q:Is the check result normal?
YES:
Go to Step 12.
NO:
Repair the wiring harness between horn (HI) connector
A-49 and horn relay connector A-15X.
STEP 12. Check the horn (HI) work normally.
ZC6045080000
Connect the battery as shown, and verify that the horn sounds.
Q:Does horn (HI) work normally?
YES:
Go to Step 13.
NO:
Replace the horn (HI). go to step 13
STEP 13. Check which horn is defective.
Check which horn does not sound when the theft-alarm system
is triggered.
Q:Which horn does not sound?
Horn (HI) and horn (LO):
Go to Step 14.
Horn (HI) only:
Replace the ETACS-ECU.
Horn (LO) only:
Go to Step 14.
STEP 14. Check horn (LO) connector A-45 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is horn (LO) connector A-45 in good condition?
YES:
Go to Step 15.
NO:
Repair the damaged parts.
STEP 15. Check the Wiring harness between horn (LO)
connector A-45 (terminal No. 1) and horn relay connector
A-15X (terminal No. 3).
Check the output lines for open circuit and short circuit.
Q:Is the check result normal?
YES:
Go to Step 16.
NO:
Repair the wiring harness between horn (LO) connector
A-45 and horn relay connector A-15X.
54Af-24
ALARM SYSTEM
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст