Mitsubishi Outlander XL. Manual — part 1071
STEP 16. Check the horn (LO) work normally.
ZC6045080000
Connect the battery as shown, and verify that the horn sounds.
Q:Does the horn (LO) work normally?
YES:
Go to Step 17.
NO:
Replace the horn (LO).go to step 18.
STEP 17. Retest the theft-alarm system.
Q:Does the theft-alarm system work normally?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO<Horn (HI) and Horn (LO) do not sound.>:
Replace the
ETACS-ECU.
NO<Horn (LO) does not sound.>:
Replace the ETACS-ECU.
NO<Horn (HI) does not sound.>:
Carry out the
troubleshooting again.
Inspection Procedure 5: Panic alarm does not work normally.
M15410300046USA0000010000
TECHNICAL DESCRIPTION (COMMENT)
If keyless operation system <KOS> or keyless entry
system <WCM> is normal, the ETACS-ECU may be
defective.
TROUBLESHOOTING HINTS
⦆
Keyless operation system <KOS> or keyless entry
system <WCM> may be defective
⦆
The ETACS-ECU may be defective
⦆
Function is not set with the customization.
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB992006: Extra fine probe
⦆
MB991223: Harness set
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
ALARM SYSTEM
54Af-25
DIAGNOSIS
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
Check if DTC is set to the KOS-ECU <Vehicles with KOS> or
WCM <Vehicles with WCM>.
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
(1)
Turn the ignition switch to the "ON" position.
(2)
Check whether the KOS or WCM related DTC is set.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES<vehicles with KOS>:
Troubleshoot the KOS (Refer to
YES<vehicles with WCM>:
Troubleshoot the WCM (Refer to
NO:
Go to Step 2.
STEP 2. Check keyless operation system <KOS> or keyless
entry system <WCM>.
Q:Do keyless operation system <KOS> or keyless entry
system <WCM> work normally?
YES:
Go to Step 3.
NO<vehicles with KOS>:
Troubleshoot the KOS (Refer to
NO<vehicles with WCM>:
Troubleshoot the WCM (Refer to
STEP 3. Using scan tool MB991958, check the configuration
function.
(1)
Turn the ignition switch to the "ON" position.
(2)
Use the KOS-ECU <vehicles with KOS> or WCM <vehicles
with WCM> configuration function to check that the "Panic
alarm switch" is set to "Enable".
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the "Panic alarm switch" set to "Enable"?
YES:
Replace the ETACS-ECU.
NO:
Use the KOS-ECU configuration function to set the
"Panic alarm switch" to "Enable"(Refer to GROUP 42B
configuration function P.42B-170. <vehicles with KOS>
54Af-26
ALARM SYSTEM
DIAGNOSIS
NO:
Use the WCM configuration function to set the "panic
alarm switch" to "Enable"(Refer to GROUP 42C
configuration function P.42C-91. <vehicles with WCM>
ON-VEHICLE SERVICE
CONFIGURATION FUNCTION
M15410300034USA0000010000
Use scan tool MB991958 to adjust the following
functions. The programmed information is held even
when the battery is disconnected.
Adjustment item
(scan
tool
display)
Adjustment item
Adjustment contents (scan tool
display)
Adjusting contents
Alarm
With/without
theft-
alarm function
Disable
Without function
Enable
With function (default)
Duration of pre-
alarm
Adjustment of pre-
alarm continue time
10 sec
10 seconds (default)
6 sec
6 seconds
Panic alarm switch With/without
panic
alarm function
Disable
Without function
Enable
With function (default)
ALARM SYSTEM
54Af-27
ON-VEHICLE SERVICE
HORN
REMOVAL AND INSTALLATION
M15410300007USA0000010000
ZC5020000000
5
2
1
3
4
18 ± 7 N·m
13 ± 5 ft-ld
18 ± 7 N·m
13 ± 5 ft-ld
18 ± 7 N·m
13 ± 5 ft-ld
18 ± 7 N·m
13 ± 5 ft-ld
Removal Steps
·
Front bumper assembly (Refer to
GROUP 51A - Front Bumper
Assembly P.51A-3.)
1.
Horn (HI)
2.
Horn (LO)
Removal Steps
3.
Horn bracket
4.
Horn (for theft-alarm)
5.
Horn harness
54Af-28
ALARM SYSTEM
HORN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст