Mitsubishi Outlander XL. Manual — part 998
STEP 3. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
tool P.54Ac-58."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
Q:Is DTC 22 set?
YES:
Go to Step 4.
NO:
The procedure is complete.
STEP 4. Check headlight automatic leveling-ECU connector
C-110 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q:Is headlight automatic leveling-ECU connector C-110 in
good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. Check the wiring harness between front height
sensor connector A-04 (terminal No. 1/2/3) and the headlight
automatic leveling-ECU connector C-110 (terminal No.
15/17/19).
NOTE:
Before the wiring harness check, check the
intermediate connector A-57, and repair that if necessary.
Q:Is wiring harness between front height sensor connector
A-04 (terminal No. 1/2/3) and the headlight automatic
leveling-ECU connector C-110 (terminal No 15/17/19) in
good condition?
YES:
Go to Step 6.
NO:
Repair the wiring harness.
STEP 6. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is DTC 22 set?
LIGHTING
54Ac-65
DIAGNOSIS
YES:
Replace the headlight automatic leveling-ECU.
NO:
The trouble, such as a poor connector connection from
the front height sensor to headlight automatic leveling-
ECU or an open circuit of wiring harness, can be an
intermittent malfunction. (Refer to GROUP 00 - How to use
Troubleshooting/inspection Service Points - How to cope
with Intermittent Malfunction P.00-15.)
DTC 23: Height sensor power supply short to ground
M15410900083USA0000010000
Before replacing the ECU, ensure that the
communication circuit is normal.
Height Sensor Power Supply Circuit
HEADLAMP
AUTOMATIC
LEVELING-ECU
HALL IC
REAR
HEIGHT
SENSOR
FRONT
HEIGHT
SENSOR
HALL IC
ZC6008710007
Connector: A-04, A-57
A-04 (B)
A-57 (GR)
54Ac-66
LIGHTING
DIAGNOSIS
ZC6008760030
Connector: C-110
ZC6008800023
Connector: D-117, D-118
D-117
D-118
ZC6008750019
Connector: C-129
TROUBLE JUDGMENT
If the front height sensor, rear height sensor power
supply, or ground line is short-circuited, DTC 23 is set.
TECHNICAL DESCRIPTION (COMMENT)
The front height sensor, the rear height sensor, the
headlight automatic leveling-ECU, or wiring harness
and connectors between the front/rear height sensor
and the headlight automatic leveling-ECU may have
a problem.
TROUBLESHOOTING HINTS
⦆
Malfunction of the front height sensor
⦆
Malfunction of the rear height sensor
⦆
Malfunction of the headlight automatic leveling-
ECU
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
LIGHTING
54Ac-67
DIAGNOSIS
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check front height sensor connector A-04 and
headlight automatic leveling-ECU connector D-110 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Are front height sensor connector A-04 and headlight
automatic leveling-ECU connector D-110 in good
condition?
YES:
Go to Step 2.
NO:
Repair the damaged parts.
STEP 2. Check the wiring harness between front height
sensor connector A-04 (terminal No. 1/3) and headlight
automatic leveling-ECU connector D-110 (terminal No.
15/19).
NOTE:
Before the wiring harness check, check the
intermediate connector A-57, and repair that if necessary.
Q:Is wiring harness between front height sensor connector
A-04 (terminal No. 1/3) and headlight automatic leveling-
ECU connector D-110 (terminal No. 15/19) in good
condition?
YES:
Go to Step 3.
NO:
Repair the wiring harness.
STEP 3. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
tool P.54Ac-58."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
Q:Is DTC 23 set?
YES:
Go to Step 4.
NO:
The trouble, such as a poor connector connection from
the front height sensor to headlight automatic leveling-
ECU or an open circuit of wiring harness, can be an
intermittent malfunction. (Refer to GROUP 00 - How to use
Troubleshooting/inspection Service Points - How to cope
with Intermittent Malfunction P.00-15.)
STEP 4. Check rear height sensor connector D-118 and
headlight automatic leveling-ECU connector D-110 for
54Ac-68
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст