Mitsubishi Outlander XL. Manual — part 999
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Are rear height sensor connector D-118 and headlight
automatic leveling-ECU connector C-110 in good
condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. Check the wiring harness between rear height
sensor connector D-118 (terminal No. 1/3) and headlight
automatic leveling-ECU connector C-110 (terminal No.
16/20).
NOTE:
Before the wiring harness check, check the
intermediate connectors C-129 and D-117, and then repair
that if necessary.
Q:Is wiring harness between rear height sensor connector
D-118 (terminal No. 1/3) and the headlight automatic
leveling-ECU connector C-110 (terminal No 15/19) in good
condition?
YES:
Go to Step 6.
NO:
Repair the wiring harness.
STEP 6. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is DTC 23 set?
YES:
Go to Step 7.
NO:
The trouble, such as a poor connector connection from
the rear height sensor to headlight automatic leveling-
ECU or an open circuit of wiring harness, can be an
intermittent malfunction. (Refer to GROUP 00 - How to use
Troubleshooting/inspection Service Points - How to cope
with Intermittent Malfunction P.00-15.)
STEP 7. Check front height sensor.
Check that the front height sensor is normal (Refer to P.
54Ac-180).
Q:Do front height sensor work normal?
YES:
Go to Step 8.
NO:
Replace the front height sensor.
STEP 8. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
LIGHTING
54Ac-69
DIAGNOSIS
Q:Is DTC 23 set?
YES:
Go to Step 9.
NO:
The procedure is complete.
STEP 9. Check rear height sensor.
Check that the rear height sensor is normal (Refer to P.
54Ac-180).
Q:Does the rear height sensor work normal?
YES:
Go to Step 10.
NO:
Replace the rear height sensor.
STEP 10. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is DTC 23 set?
YES:
Replace the headlight automatic leveling-ECU.
NO:
The procedure is complete.
DTC 24: Pitch angle abnormality
M15410900084USA0000010000
Before replacing the ECU, ensure that the
communication circuit is normal.
54Ac-70
LIGHTING
DIAGNOSIS
Height Sensor Power Supply Circuit
HEADLAMP
AUTOMATIC
LEVELING-ECU
HALL IC
REAR
HEIGHT
SENSOR
FRONT
HEIGHT
SENSOR
HALL IC
ZC6008760030
Connector: C-110
ZC600871
Connector: A-04
A-04 (B)
LIGHTING
54Ac-71
DIAGNOSIS
ZC6008800024
Connector: D-118
TROUBLE JUDGMENT
The headlight automatic leveling-ECU receives a
vehicle height signal from the front and rear height
sensors and calculates the headlight leveling pitch
angle. If an abnormal pitch angle is calculated, DTC
24 is set.
TECHNICAL DESCRIPTION (COMMENT)
The front height sensor, the rear height sensor or the
headlight automatic leveling-ECU may have a
problem.
TROUBLESHOOTING HINTS
⦆
Malfunction of the front height sensor
⦆
Malfunction of the rear height sensor
⦆
Malfunction of the headlight automatic leveling-
ECU
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check front height sensor connector A-04 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is the check result normal?
YES:
Go to Step 2.
NO:
Repair the damaged parts.
STEP 2. Check front height sensor.
Check that the front height sensor is normal (Refer to P.
54Ac-180).
Q:Do front height sensor work normal?
YES:
Go to Step 3.
NO:
Replace the front height sensor.
54Ac-72
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст