Mitsubishi Outlander XL. Manual — part 963

Tool

Tool number and
name

Supersession

Application

YB9912230000

Do not use

MB991223

MB991219

MB991220

MB991221

MB991222

Harness set

Test harness

LED harness

LED

harness

adaptor

Probe

General service tools Continuity check and voltage

measurement at harness wire or
connector for loose, corroded or
damaged terminals, or terminals
pushed back in the connector.

Connector

contact

pressure inspection

Power circuit inspection

Commercial tester connection

MB992006

MB992006
Extra fine probe

Making voltage and resistance
measurement

during

troubleshooting

MB990784

MB990784
Ornament remover

General service tool

Removal of switch, trim, etc.

DIAGNOSIS

STANDARD FLOW OF DIAGNOSTIC

TROUBLESHOOTING

M15410100086USA0000010000

Refer to GROUP 00, Contents of troubleshooting P.00-6.

DIAGNOSTIC FUNCTION

M15410100006USA0000010000

HOW TO CONNECT THE SCAN TOOL (M.U.T.-III)

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicles Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)

COMBINATION METER

54Ab-5

DIAGNOSIS

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Ensure that the ignition switch is at the "LOCK" (OFF) position.

Start up the personal computer.

Connect special tool MB991827 to special tool MB991824 and
the personal computer.

Connect special tool MB991910 to special tool MB991824.

Connect special tool MB991910 to the data link connector.

Turn the power switch of special tool MB991824 to the "ON"
position.

NOTE:

When special tool MB991824 is energized, special

tool MB991824 indicator light will be illuminated in a
green color.

Start the M.U.T.-III system on the personal computer.

NOTE:

Disconnecting scan tool MB991958 is the reverse of

the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.

HOW TO READ AND ERASE DIAGNOSTIC

TROUBLE CODES

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicles Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)

NOTE:

If the battery voltage is low, diagnostic trouble

codes will not be set. Check the battery if scan tool
MB991958 does not display.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "System select" from the start-up screen.

Select "From 2006 MY" of "Model Year." When the "Vehicle
Information" is displayed, check the contents.

Select "Meter" from "System List," and press the "OK" button.

NOTE:

When the "Loading Option Setup" list is displayed,

check the applicable item.

Select "Diagnostic Trouble Code."

If a DTC is set, it is shown.

Choose "Erase DTCs" to erase the DTC.

HOW TO DIAGNOSE THE CAN BUS LINES

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicles Communication Interface (V.C.I.)

54Ab-6

COMBINATION METER

DIAGNOSIS

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "CAN bus diagnosis" from the start-up screen.

When the vehicle information is displayed, confirm that it
matches the vehicle being diagnosed.

｠

If they match, go to step 8.

｠

If not, go to step 5.

Select the "view vehicle information" button.

Enter the vehicle information and select the "OK" button.

When the vehicle information is displayed, confirm again that
it matches the vehicle being diagnosed.

｠

If they match, go to step 8.

｠

If not, go to step 5.

Select the "OK" button.

When the optional equipment screen is displayed, choose the
one which the vehicle is fitted with, and then select the "OK"
button.

CHECK OF FREEZE FRAME DATA

The freeze frame data can be checked by using the
scan tool (GROUP 00, How to Cope with Intermittent
Malfunction P.00-15).

When detecting fault and storing the DTC, the ECU
connected to CAN bus line obtains the data before the

determination of the DTC and the data when the DTC
is determined, and then stores the ECU status of that
time. By analyzing each data from scan tool, the
troubleshooting can be performed more efficiently.
The displayed items are as the table below.

Display item list

Item No.

Item name

Data item

Unit

Odometer

Total driving distance after the diagnosis code is

generated

km*

Ignition cycle Number of times the ignition switch is turned "ON" or

"LOCK (OFF)" after the past failure transition

Number of

counts is

displayed.

Current trouble

accumulative time

Cumulative time for current malfunction of diagnosis

code

min

NOTE:

*: If a failure occurs to both the ABS-ECU

and ETACS-ECU, 0000 km or FFFF km is displayed on
the scan tool MB991958.

DIAGNOSTIC TROUBLE CODE CHART

M15410100007USA0000010000

｠

During troubleshooting, a DTC code associated
with other system may be set when the ignition
switch is turned on with connector(s)
disconnected. On completion, check all

systems for DTC code(s). If DTC code(s) are set,
erase them all.

COMBINATION METER

54Ab-7

DIAGNOSIS

｠

When the combination meter is required to be
replaced as a result of the troubleshooting, the
current driving distance and number of elapsed
days to be used for service reminder function
must be entered into the meter after the
replacement. Therefore, read "Integrated
mileage for reminder," "Integrated days for
reminder," "Mileage until Extra reminder,"
"Months until Extra reminder," and "Current
Schedule" from the meter before the
replacement using the special function of scan
tool MB991958, and note them. For the
operation method of scan tool MB991958, refer

to P.54Ab-70. If "Integrated mileage for
reminder" or "Integrated days for reminder"
cannot be read by the scan tool MB991958,
follow the method described below.

For the driving distance for check warning,
use the driving distance displayed on the
multi information display.

For the elapsed days for check warning,
calculate the number of elapsed days from
the delivery date to the customer (service
remainder function start date) and current
date.

Diagnostic trouble code
number

Diagnostic item

Reference page

B1200

Malfunction of odometer

P.54Ab-9

B1201

Abnormal fuel information

P.54Ab-10

B1202

Abnormal fuel2 information

B1208