Mitsubishi Outlander XL. Manual — part 964
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC B1200: Malfunction of odometer
M15410100009USA0000010000
TROUBLE JUDGMENT
If the odometer information, which is stored in the
combination meter, is abnormal when the ignition
switch at the ON position and the system voltage is 10
-16 volts (data from ETACS-ECU), DTC B1200 is
stored.
TROUBLESHOOTING HINTS
The combination meter may be defective.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, read the combination
meter diagnostic trouble code.
Check if DTC is set to the combination meter.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if diagnosis code is set.
Q:Is the DTC set?
YES:
Replace the combination meter, and then go to Step
2.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to Cope with Intermittent Malfunction P.
00-15).
STEP 2. Recheck for diagnostic trouble code.
Check if DTC is set to the combination meter.
(1)
Erase the DTC.
COMBINATION METER
54Ab-9
DIAGNOSIS
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if diagnosis code is set.
Q:Is the DTC set?
YES:
Go to Step 1.
NO:
The procedure is complete.
DTC B1201: Abnormal fuel information
54Ab-10
COMBINATION METER
DIAGNOSIS
DTC B1202: Abnormal fuel2 information
M15410100010USA0000010000
Fuel Level Sensor Circuit
INTERFACE
CIRCUIT
COMBINATION
METER
CPU
FUEL
LEVEL
SENSOR
(SUB)
FUEL
PUMP
MODULE
FUEL LEVEL
SENSOR
(MAIN)
COMBINATION METER
54Ab-11
DIAGNOSIS
ZC6008750036
Connectors: C-03, C-31
D-03
D-31
ZC6008790028
Connectors: D-05, D-22
D-05
D-22
ZC6008800030
Connector: D-20
D-20 (GR)
Whenever the ECU is replaced, ensure that the
communication circuit is normal.
TROUBLE JUDGMENT
With the ignition switch at the ON position and the
system voltage at 10 -16 volts (data from ETACS-
ECU), if the combination meter detects the abnormal
resistance of fuel level sensor circuit for 64 seconds
continuously, DTC B1201 or DTC B1202 is stored.
TROUBLESHOOTING HINTS
⦆
The fuel pump module [fuel level sensor (main)]
may be defective. <FWD, AWD>
⦆
The fuel level sensor (sub) may be defective.
<AWD>
⦆
The combination meter may be defective.
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991223: Harness Set
⦆
MB992006: Extra Fine Probe
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check the malfunctioning vehicle.
Q:Is the malfunctioning vehicle a FWD?
YES<FWD>:
Go to Step 2.
54Ab-12
COMBINATION METER
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст