Mitsubishi Outlander XL. Manual — part 8
GROUP 2
BODY DIMENSIONS
CONTENTS
BODY DIMENSIONS AND MEASUREMENT
METHODS. . . . . . ..
TYPE A (PROJECTED DIMENSIONS).
UNDER BODY. . . . . ...
SUSPENSION INSTALLATION DIMENSIONS
. . . . . . . . .
TYPE B (ACTUAL-MEASUREMENT
DIMENSIONS). . . . . ..
UNDER BODY. . . . . ...
SUSPENSION INSTALLATION DIMENSIONS
. . . . . . . ....
FRONT BODY. . . . . ..
SIDE BODY. . . . . ...
REAR BODY. . . . . ...
INTERIOR. . . . . ....
2-1
BODY DIMENSIONS AND MEASUREMENT
METHODS
M40200000010USA0000010000
ZB600171
Projected dimension
Height
Probe
0000
ZB6001720000
Actual-measured dimension
A
A'
ZB6001730000
Center of hole
ZB6001740000
⦆
Type A (projected dimensions) is the dimension when a
measurement location is projected onto the plane.
NOTE:
The height indicates a distance from the assumed
standard line established 100 mm below the lowest
measurement point.
⦆
Type B (actual-measurement dimensions) is the actual
distance between the measurement points. Measure using a
tracking gauge or a measuring tape, etc.
NOTE:
⦆
Make the lengths of the tracking gauge probes the same
(A=A’).
⦆
Do not bend or twist the measuring tape.
⦆
Insert the tracking gauge probes securely into the
measurement holes.
⦆
When the standard dimensions in the illustration are enclosed
by rectangle, this indicates that the symmetrical left and right
positions have the same dimensions.
⦆
When using a notch for dimension measurement, set the
measuring point at the center of the notch.
⦆
When measuring the suspension mounting arm, or link
mounting position, use the suspension mounting bolt, etc.
(Type B only)
⦆
The body center points are shown for the purpose of checking
the position of the left and right symmetry location.
2-2
BODY DIMENSIONS
BODY DIMENSIONS AND MEASUREMENT METHODS
ZB6001750000
Bolt
Measurement point
TYPE A (PROJECTED DIMENSIONS)
UNDER BODY
M40200000050USA0000010000
AB501333
ZB5004330000
2
1
5
3
4
7
6
8
9
10
11
12
13
Center line of the vehicle
mm (in)
651
(25.6)
540
(21.3)
350
(13.8)
374
(14.7)
701
(27.6)
752
(29.6)
833
(32.8)
440
(17.3)
393
(15.5)
628
(24.7)
111
(4.4)
510
(20.0)
960
(37.8)
910
(35.8)
564
(22.2)
375
(14.8)
624
(24.6)
875
(
34.4
)
462
(18.2)
894
(35.2)
894
(35.2)
877
(34.5)
197
(7.8)
967
(38.0)
1,050
(41.3)
1,009
(39.7)
1,022
(40.2)
1,056
(41.6)
1,262
(49.7)
ZB5004340000
2
1
5
3
4
7
6
8
9
10
11
12
13
mm (in)
Center line of the vehicle
960
(37.8)
641
(
25.2
)
544
(
21.4
)
763
(30.0)
972
(38.3)
967
(38.1)
686
(
27.0
)
1,272
(50.1)
1,217
(47.9)
1,218
(48.0)
1,025
(40.4)
1,149
(45.2)
1,448
(57.0)
1,342
(52.8)
1,126
(44.3)
1,138
(44.8)
1,028
(40.5)
1,079
(42.5)
1,394
(54.9)
1,140
(44.9)
1,144
(45.0)
BODY DIMENSIONS
2-3
TYPE A (PROJECTED DIMENSIONS)
No. Standard measurement point
Hole
shape
Size mm (in)
1
Center of front end crossmember lower water draining hole (Left side)
Round 8 (0.3)
2
Center of front end crossmember lower water draining hole (Right side)
Round 8 (0.3)
3*
Center of front sidemember inner positioning hole
Round 25 (1.0)
4*
Center of front suspension crossmember mounting hole
Round 15.5 (0.6)
5*
Center of front sidemember rear water draining hole
Round 16 (0.6)
6*
Center of front floor sidemember front positioning hole
Round 16 (0.6)
7*
Center of front floor sidemember front positioning hole
Round 16 (0.6)
8*
Center of rear floor sidemember lower positioning hole
Oblong 33.9×18
(1.3×0.7)
9*
Center of rear floor sidemember lower water draining hole
Round 18 (0.7)
10* Center of rear floor sidemember lower positioning hole
Round 25 (1.0)
11* Center of trailer hitch mounting hole
Round 15 (0.6)
12
Center of center bearing mounting hole
Round 11 (0.4)
13
Center of center bearing mounting hole
Round 11 (0.4)
NOTE:
The * mark indicates the mounting position
for the frame centering gauge.
AB501337
ZB5004350000
2
1
5
3
4
7
6
8
9
10
12
11
13
mm (in)
Standard line
280
(11.0)
279
(11.0)
347
(13.7) 294
(11.6)
510
(20.1)
716
(28.2)
750
(29.5)
286
(11.3)
354
(13.9)
357
(14.1)
350
(13.8)
326
(12.8)
259
(10.2)
486
(19.1)
230
(9.1)
100
(3.9)
157
(6.2)
105
(4.1)
105
(4.1)
154
(6.1)
1,049
(41.3)
1,136
(44.7)
1,758
(69.2)
1,160
(45.7)
NOTE:
The assumed standard line is established
100 mm (3.9 inches) below the measurement point
No.5.
2-4
BODY DIMENSIONS
TYPE A (PROJECTED DIMENSIONS)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст