Mitsubishi Outlander XL. Manual — part 1315
Windshield wiper linked with washer function Initial condition: with function, with windshield washer
check valve
ZC5012810000
t
t
T
T
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Windshield wiper
auto stop signal
Windshield washer relay
Windshield washer switch
Windshield wiper
drive signal
Wiper switch in
off position
Wiper switch in intermittent
operation position
t: 0.3 second
T: Intermittent wiper intermittent time
Wiper switch
OFF position
Intermittent operation position
Low-speed
or
high-speed
operation
position
Washer switch ON
time(t)
0.3
second
or less
0.3
to
0.5
second
0.5
second
or more
0.2
second
or less
0.2 to
0.4
second
0.4
to
0.6
second
0.6
second
or more
-
T
0
second
2
seconds
3
seconds
0
second
1
second
2
seconds
3
seconds
3 seconds
When the windshield washer switch on the column
switch is turned ON while the ignition switch is in ACC
or ON position, ETACS turns the windshield washer
relay ON.
When the windshield washer switch is kept ON for 0.3
seconds or longer, the windshield wiper drive signal
(the wiper drive signal output time varies depending
on the conditions. For details, see the table.) is turned
ON, and the windshield wiper operates at high speed.
The windshield wiper is turned OFF with 3 seconds
delay after the windshield washer switch is turned
OFF.
Even when the windshield washer switch is turned ON
while the windshield wiper is operating intermittently,
the intermittent action starts again after the linked
operation is finished.
If the ignition switch is turned to ACC position while
the windshield washer switch is ON, the windshield
washer relay turns ON, but the windshield wiper does
not perform the linked operation. When the windshield
washer switch is turned OFF and then ON, the
windshield wiper starts the linked operation.
NOTE:
⦆
Using the configuration function, the washer linked
windshield wiper function can be turned off. (Refer
to P.51-13.)
⦆
Using the configuration function, when the washer
linked windshield wiper function is turned off, only
the washer operates. It is useful to melt down ice on
a frozen windshield.
51-10
EXTERIOR
REAR WIPER AND WASHER
REAR WIPER AND WASHER
M25100000080USA0000010000
CONSTRUCTION DIAGRAM
ZC6002320000
Tailgate spoiler
Rear wiper arm
Rear wiper blade
Rear wiper hose
Rear washer
nozzle
Rear wiper
motor
⦆
Resin wiper arm has been adopted to achieve
weight reduction and integration of the arm and
blade.
⦆
Fixed interval type intermittent wiper* provides a
clear rear view in rainy weather.
⦆
The washer tank is shared with the windshield
washer.
⦆
The initial continuous operation function has been
adopted. In this function, the rear wiper performs
continuous low-speed operation for 2 to 3 cycles to
sweep the raindrops away from the rear windshield
after the rear wiper switch is turned on, and then
proceeds with intermittent operation.
⦆
Reverse gear-linked rear wiper function has been
adopted. In this function, the rear wiper performs
continuous low-speed operation for 2 to 3 cycles
approximately 1 second after the selector lever is
shifted to “R” position while the rear wiper switch is
in the intermittent position, and then proceeds with
intermittent operation.
⦆
Washer-linked wiper function* has been adopted.
Washer fluid can be optionally injected without
operating the wiper. When the ignition switch is
turned ON while the washer switch is ON, the
washer motor operates but the wiper does not.
NOTE:
*: Using the configuration function, the
fixed interval type intermittent wiper and the
washer-linked wiper function can be adjusted.
(Refer to P.51-13.)
EXTERIOR
51-11
REAR WIPER AND WASHER
DESCRIPTION OF CONSTRUCTION AND OPERATION
Rear wiper control [Initial condition: 8 seconds (without successive operations)]
ZC5013040000
t
ON
OFF
ON
OFF
ON
OFF
T2
T3
T2
T3
T1
T4
T4
T1
T4
T4
T4
T3
T2
T2
T2
T2: 7.4 seconds
Rear wiper drive signal
Rear wiper switch
Inhibitor switch "R" position
T1: 3.0 seconds
t: 1.0 second
T3: 8.0 seconds
T4: 0.6 second
1.
When the rear wiper switch on the column switch
is turned ON while the ignition switch is in ACC or
ON position, ETACS turns the rear wiper drive
signal ON for 3 seconds (for approximately 2
cycles) and operates the intermittent action in 8
second intervals.
When the selector lever is moved to R (reverse)
position during the rear wiper operation, the
transmission range switch R (reverse) turns ON,
and one second after that, ETACS turns the rear
wiper drive signal ON for 3 seconds (for
approximately 2 cycles), and operates the
intermittent action in 8 second intervals again.
2.
By the special operation of the rear wiper switch
on the column switch (2 consecutive operations),
the rear wiper can operate continuously regardless
of the set intermittent time.
NOTE:
Using the configuration function, the rear
wiper intermittent time can be adjusted. (Refer
to P.51-13.)
Rear wiper linked with washer function Initial condition: with function
ZC5013050000
t : 0.3 second
T4 : 0.6 second
T1 : 3 seconds
T2 : 7.4 seconds
T3 : 8 seconds
t
t
t
ON
OFF
ON
OFF
ON
OFF
T1
T1
T1
T2
T3
T4
T4
Rear wiper switch
in OFF position
Rear wiper switch in ON position
Rear washer switch
Rear washer relay
Rear wiper drive
signal
When the rear washer switch on the column switch is
turned ON while the ignition switch is in ACC or ON
position, ETACS turns the rear washer relay ON.
51-12
EXTERIOR
REAR WIPER AND WASHER
The rear washer relay turns ON after the rear washer
switch has been ON for 0.3 second, then turns the rear
wiper drive signal ON to operate the rear wiper
simultaneously. When the rear washer switch is
turned OFF, after 3 seconds the rear wiper is turned
OFF.
If the rear washer switch is turned ON during the rear
wiper operation, 7.4 seconds after turning OFF the
rear wiper drive signal turns OFF, the intermittent
action is resumed in 8 second intervals.
NOTE:
Using the configuration function, the
washer linked rear wiper function can be turned
off. (Refer to P.51-13.)
OUTSIDE MIRROR
M25100000081USA0000010000
CONSTRUCTION DIAGRAM
ZC6002290001
Door mirror assembly
Mirror glass
Remote control
mirror switch
Door mirrors have the following features:
⦆
Remote controlled door mirrors have been adopted.
⦆
Door mirrors with heater element have been
adopted.
⦆
Large size mirror glass has been adopted for easy
confirmation of safety around the vehicle.
⦆
Low air resistance door mirror shape has been
introduced.
⦆
Flag type which secures sufficient distance
between the door mirror and delta pillar has been
adopted to reduce the blind spot area of the forward
view.
CONFIGURATION FUNCTION
M25100000092USA0000010000
Using the M.U.T.-III scan tool, the following functions
can be programmed. The programmed information is
kept in memory even when the battery is
disconnected.
EXTERIOR
51-13
OUTSIDE MIRROR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст