Mitsubishi Outlander XL. Manual — part 1204
A/C COMPRESSOR CLUTCH RELAY CONTINUITY
CHECK
ZC603579
4
1
2
3
3
1
4
2
A/C compressor clutch relay
Battery voltage
Tester connection Specified
condition
Not applied
3 - 4
Open circuit
⦆
Connect terminal
2 to the positive
battery terminal
⦆
Connect terminal
1 to the negative
battery terminal
3 - 4
Less than 2 ohms
AIR CONDITIONING
55A-107
ON-VEHICLE SERVICE
FAN CONTROL RELAY CONTINUITY CHECK
ZC603579
2
1
5
4
3
3
1
5
4
2
Fan control relay
Battery voltage
Tester connection Specified
condition
Not applied
2 - 4
Open circuit
⦆
Connect terminal
1 to the positive
battery terminal
⦆
Connect terminal
3 to the negative
battery terminal
2 - 5
Less than 2 ohms
55A-108
AIR CONDITIONING
ON-VEHICLE SERVICE
CONDENSER FAN RELAY CONTINUITY CHECK
ZC603579
3
1
4
2
2
1
4
3
Condenser fan relay
Battery voltage
Tester connection Specified
condition
Not applied
2 - 4
Open circuit
⦆
Connect terminal
3 to the positive
battery terminal
⦆
Connect terminal
1 to the negative
battery terminal
2 - 4
Less than 2 ohms
IDLE-UP OPERATION CHECK
M15502000016USA0000010000
1.
Before inspection and adjustment, set vehicle in the following
condition:
⦆
Engine coolant temperature: 80 - 90 °C (176.0 - 194.0 °F)
⦆
Lights, electric cooling fan and accessories: OFF
⦆
Transaxle: Neutral ("N" or "P" position)
⦆
Steering wheel: Straightforward
2.
Check whether or not the idle speed is the standard value.
Refer to GROUP 11A, On-vehicle Service - Idle Speed
Check P.11A-16.
Standard value: 650 ± 50 r/min
3.
Turn on the A/C switch and the blower speed selection dial.
Engine idling speed should be within the standard value:
AIR CONDITIONING
55A-109
ON-VEHICLE SERVICE
Standard value: 800 ± 50 r/min
NOTE:
The powertrain control module determines whether
the A/C load is low or high according to the output signal
from the A/C-ECU.
NOTE:
It is not necessary to make an adjustment, because
the idling speed is automatically adjusted by the ISC
system. If, however, a deviation from the standard value
occurs for some reason, check the ISC system. (Refer to
GROUP 11A, On-vehicle Service - Idle Speed Check P.
11A-16)
REPLACE THE CLEAN AIR FILTER
M15502000201USA0000010000
ZC6039050000
1.
Remove the glove box (Refer to GROUP 52A - Instrumental
Panel, P.52A-2).
2.
Loosen the two lugs as shown to replace the clean air filter.
3.
Install the glove box.
A/C CONTROL PANEL ASSEMBLY
REMOVAL AND INSTALLATION
M15502000018USA0000010001
Pre-removal and Post-installation Operation
⦆
Center Panel Assembly Removal and Installation (Refer to GROUP 52A - Instrument Panel P.52A-2).
⦆
Lower Side Cover Removal and Installation (Refer to GROUP 52A - Floor Console P.52A-8.)
ZC600424
2
1
0000
Removal steps
1.
Lower panel
Removal steps
2.
A/C control panel
55A-110
AIR CONDITIONING
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст