Mitsubishi Outlander XL. Manual — part 702
ZC601752AA00
Brake grease: Chuo Yuka AKB100
1
2
3
4
5
6
7
7
8
9
10
11
12
20
19
21
13
13
14
14
15
16
17
18
10
11
N
N
Backing plate
60 ± 5 N·m
45 ± 3 ft-lb
Removal steps
<<A>>
1.
Rear brake caliper assembly
2.
Rear brake disc
>>D<<
3.
Shoe-to-anchor spring
>>D<<
4.
Shoe-to-anchor spring
5.
Shoe guide plate
6.
Adjusting wheel spring
>>C<<
7.
Adjuster assembly
8.
Strut
9.
Strut shoe-to-spring
10. Shoe hold down cup
11. Shoe hold down spring
Removal steps
12. Shoe hold down pin
13. Shoe and lining assembly
14. Shoe and lever assembly
<<B>>
>>B<<
15. Retainer
>>A<<
16. Wave washer
17. Parking lever
18. Shoe and lining assembly
19. Pin
20. Parking brake rear cable
21. O-ring
REMOVAL SERVICE POINTS
<<A>> REAR BRAKE CALLIPER ASSEMBLY REMOVAL
Remove the rear brake calliper assembly and hold it with a wire.
PARKING BRAKES
36-15
PARKING BRAKE LINING AND DRUM
<<B>> RETAINER REMOVAL
4
ZC5012550000
Pin of shoe and lining assembly
Retainer
Use a flat-tipped screwdriver or the like to open up the retainer
joint, and remove retainer.
INSTALLATION SERVICE POINTS
>>A<< WAVE WASHER INSTALLATION
ZC6020170000
Shoe and lining
assembly
Parking lever
Wave washer
Retainer
Install the wave washer in the direction shown in the illustration.
>>B<< RETAINER INSTALLATION
AC000926
ZC5012560000
Pin of shoe and lining assembly
Retainer
Use pliers or the like to close the retainer end onto the pin.
36-16
PARKING BRAKES
PARKING BRAKE LINING AND DRUM
>>C<< ADJUSTER ASSEMBLY INSTALLATION
ZC6017620000
Shoe adjusting bolt
Install the adjuster assemblies. Install the adjuster assembly with
the left side of the shoe adjusting bolt facing forward of the
vehicle, and the right side facing rearward.
>>D<< SHOE-TO-ANCHOR SPRING INSTALLATION
ZC6017610000
Front of the vehicle
Blue paint
Yellow paint
The shoe-to-anchor springs are not interchangeable because
their spring loads are different. The one with blue paint mark
should be installed to the front of the vehicle, and the other with
yellow paint to the rear of the vehicle, respectively.
NOTE:
The figure describes the left rear wheel. The right
rear wheel is symmetrical to that.
BRAKE LINING THICKNESS CHECK
M13601000901USA0000010000
ZC600958 0000
1.
Measure the lining thickness at the most worn area.
Standard value: 2.8 mm
Limit: 1.0 mm
2.
If the thickness is less than the limit value, replace the right
and left shoe and lining assemblies as a set.
BRAKE DRUM INSIDE DIAMETER CHECK
M13601000902USA0000010001
ZC6009590000
1.
Measure the inside diameter of the brake drum at two
positions or more.
Standard value: 190.0 mm
Limit: 191.0 mm
2.
If the inside diameter is more than limit value or if there is
excessive wear, replace the brake disc.
PARKING BRAKES
36-17
PARKING BRAKE LINING AND DRUM
MEMO
36-18
PARKING BRAKES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст