Mitsubishi Outlander XL. Manual — part 701
ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE CHECK AND
ADJUSTMENT
M13601000009USA0000010000
STROKE CHECK (CONTROL FORCE APPROXIMATELY 200
N)
Standard value: 3 to 5 notches
STROKE ADJUSTMENT
If the parking brake lever stroke is out of the standard range,
adjust as described below:
1.
Remove the rear floor console assembly. (Refer to GROUP
52A - Rear Floor Console Assembly P.52A-9.)
ZC6009510000
Adjusting nut
Cable rod
2.
Loosen the adjusting nut to the end of the cable rod in order
to allow slack in the cables.
ZC600952 0000
Adjuster
3.
Remove the rear brake disc adjusting hole plug. Then insert
a flat-tipped screwdriver to turn the adjuster to the arrow
direction (to expand the shoe) until the parking brake shoe
makes contact and the disc can no longer be turned. Back off
the adjuster to the opposite direction by five notches.
ZC6009510000
Adjusting nut
Cable rod
Be careful that the parking brake lever notch number should
be within the standard range. If the notch number is too low,
rear brake dragging can be caused.
4.
Adjust the parking brake lever stroke to the standard value by
turning the adjusting nut. After adjustment, check that there is
no free play between the adjusting nut and the parking brake
lever.
5.
After the parking brake lever stroke is adjusted, raise the rear
of the vehicle. Release the parking brake, and turn the rear
wheels to confirm that the rear brakes are not dragging.
PARKING BRAKES
36-11
ON-VEHICLE SERVICE
PARKING BRAKE SWITCH CHECK
M13601000033USA0000010000
1.
Remove the rear floor console assembly. (Refer to GROUP
52A - Rear Floor Console P.52A-9.)
ZC6009510001
2.
Check for continuity between the parking brake switch
terminal and the switch mounting bolt.
When the parking brake
lever is pulled up:
Continuity exists
When the parking brake
lever is released:
No continuity
PARKING BRAKE LINING SEATING PROCEDURE
M13601000011USA0000010000
Perform lining seating in a place with good visibility, and
pay special attention to safety.
Perform lining seating by the following procedure when replacing
the parking brake shoe assemblies or the rear brake discs, or
when brake performance is insufficient.
1.
Adjust the parking brake lever stroke to the standard value
(Refer to P.36-11).
ZC603529AA00
Spring scale
Pull
Approximately
40 mm (1.6 in)
2.
Hook a spring scale onto the center of the parking brake lever
grip and pull it with a force of 98 - 147 N (22 - 33 pounds) in a
direction perpendicular to the handle.
3.
Drive the vehicle at a constant speed of 35 - 50 km/h (22 - 31
mph) for 100 meters (328 feet).
4.
Release the parking brake and let the brakes cool for five to
ten minutes.
5.
Repeat the procedure in steps 2. to 4. four to five times.
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
M13601000013USA0000010000
Pre-removal operation
Rear Floor Console Assembly Removal (Refer to GROUP 52A
- Rear Floor Console P.52A-9.)
Post-installation operation
⦆
Parking Brake Lever Stroke Check (Refer to P.36-11.)
⦆
Rear Floor Console Assembly Installation (Refer to GROUP
52A - Rear Floor Console P.52A-9.)
36-12
PARKING BRAKES
ON-VEHICLE SERVICE
AC506641
ZC600953AA00
Section A – A
Section B – B
Section C – C
Section D – D
A
A
B
B
C
C
D
D
1
2
3
4
5
20 ± 5 N·m
15 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
N
Removal steps
1.
Parking brake switch connector
2.
Adjusting nut
3.
Parking brake rear cable connection
Removal steps
4.
Parking brake lever assembly
5.
Parking brake switch
PARKING BRAKE CABLE
REMOVAL AND INSTALLATION
M13601000019USA0000010000
Pre-removal operation
⦆
Rear Floor Console Assembly Removal (Refer to GROUP
52A - Rear Floor Console Assembly P.52A-9.)
⦆
Rear Seat Assembly Removal (Refer to GROUP 52A - Rear
Post-installation operation
⦆
Rear Seat Assembly Installation (Refer to GROUP 52A - Rear
⦆
Rear Floor Console Assembly Installation (Refer to GROUP
52A - Rear Floor Console Assembly P.52A-9.)
⦆
Parking Brake Lever Stroke Check and Adjustment (Refer to P.
PARKING BRAKES
36-13
PARKING BRAKE CABLE
ZC6019930000
1
2
5
3
N
2
3
N
4
5
5
5
5 <AWD>
5
5 <FWD>
Removal steps
·
Release the parking brake lever.
1.
Parking brake front cable and parking
brake rear cable connection
2.
Clip
·
Shoe and lining assembly (Refer to P.
36-14.)
Removal steps
3.
O-ring
4.
Parking brake rear cable
5.
Clip
PARKING BRAKE LINING AND DRUM
REMOVAL AND INSTALLATION
M13601000025USA0000010000
36-14
PARKING BRAKES
PARKING BRAKE LINING AND DRUM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст