Mitsubishi Outlander XL. Manual — part 1023
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00 - How to use Troubleshooting/
inspection Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the ETACS-ECU.
HEADLIGHT
ON-VEHICLE SERVICE
HEADLIGHT AIMING
M15410900017USA0000010000
PRE-AIMING INSTRUCTIONS (LOW-BEAM)
1.
Inspect for rusted or faulty headlight assemblies.
2.
These conditions must be corrected before a satisfactory
adjustment can be made.
3.
Inspect tire inflation, and adjust if necessary.
4.
If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [3 kg (6.6 pounds) per
gallon].
5.
There should be no other load in the vehicle other than driver
or substituted weight of approximately 68 kg (150 pounds)
placed in driver's position.
6.
Thoroughly clean headlight lenses.
7.
Place the vehicle on a level floor, perpendicular to a flat screen
7.62 m (25.0 ft) away from the bulb center-marks on the
headlight lens.
8.
Rock vehicle sideways to allow vehicle to assume its normal
position.
9.
Bounce the front suspension through three (3) oscillations by
applying the body weight to hood or bumper.
LIGHTING
54Ac-165
HEADLIGHT
ZC6017830000
(1)
(2)
(3)
(3)
Vehicle center line
Screen
Headlight center line
6.72 m
Light center
10.
Set the distance between the screen and the bulb center
marks of the headlight as shown in the illustration.
11.
Four lines of adhesive tape (or equivalent markings) are
required on screen or wall:
(1)
Position a vertical tape or mark so that it is aligned with
the vehicle center line.
(2)
Measure the distance from the center-marks on the
headlight lens to the floor [ reference value: 828 mm (3.26
inches)]. Transfer the measurement to the screen.
Horizontal tape or mark on the screen is for reference of
vertical adjustment.
(3)
Measure the distance from the center line of the vehicle
to the center of each headlight. Transfer the
measurement to the screen. Vertical tape or mark on the
screen with reference to the center line of each headlight
bulb.
HEADLIGHT ADJUSTMENT (LOW-BEAM)
NOTE:
When adjusting headlight, disconnect the other
headlight harness.
1.
The low beam headlight will project on the screen upper edge
of the beam (cut-off).
54Ac-166
LIGHTING
HEADLIGHT
ZC603337
ZC603076
ZC603619
ZC604537
0000
Vertical direction
adjustment
Adjustment screw
Vertical direction
adjustment
Adjustment screw
Vertical direction adjustment
<Halogen headlight>
<Discharge headlight>
ZC603633
(H)
(V)
mm (in)
0000
50.5 (2.0)
50.5 (2.0)
Hot zone
Cutoff
line
126.4 (5.0)
126.4 (5.0)
266.1 (10.5)
2.
Turn the adjusting screws to achieve the specified low-beam
cut-off location on the aiming screen.
Standard value:
(Vertical direction) Horizontal line (H) ± 50.5 mm (±
2.0 inches) (0.38 degrees angle)
(Horizontal direction): ± 126.4 mm (± 5.0 inches) (±
0.95 degrees angle) from the axis, which is 266.1
mm (10.5 inches) (2 degrees angle) rightward from
the vertical line (V)
Do not cover a headlight for more than three minutes to
prevent the plastic headlight lens deformation.
NOTE:
High-beam pattern should be correct when the low-
beams are adjusted properly.
LUMINOUS INTENSITY MEASUREMENT
M15410900018USA0000010000
1.
Set the headlights to high-beam.
2.
Using a photometer, and following its manufacturer's
instruction manual, measure the headlight center intensity and
check to be sure that the limit value is satisfied.
LIGHTING
54Ac-167
HEADLIGHT
Limit: 40,000 cd or more {When a screen is set 18.3m
(60 feet) ahead of the vehicle}
NOTE:
When measuring the intensity, maintain an engine
speed of 2,000 r/min, with the battery fully charged.There
may be special local regulations pertaining to headlight
intensity. Be sure to make any adjustments necessary to
satisfy such regulations.If an illuminometer is used to
make the measurements, convert its values to photometer
values by using the following formula.
I =E × r2Where:
⦆
I = intensity (cd)
⦆
E = illumination (lux)
⦆
r = distance (m) from headlights to illuminometer
REPLACE THE BULB.
M15410900019USA0000010000
HEADLIGHT BULB (LOW-BEAM) REPLACEMENT
<VEHICLES WITHOUT DISCHARGE HEADLIGHT>
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
ZC603076 0000
Headlight bulb
(low-beam)
Disconnect the connector, and twist the headlight bulb (low-
beam) to remove.
HEADLIGHT BULB (HIGH-BEAM) REPLACEMENT
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
54Ac-168
LIGHTING
HEADLIGHT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст