Mitsubishi Outlander XL. Manual — part 1024
ZC603076
Headlignht bulb
(high-beam)
0001
Disconnect the connector, and twist the headlight bulb (high-
beam) to remove.
POSITION LIGHT BULB REPLACEMENT
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
ZC3052770000
Position light
Disconnect the connector, and twist the position light socket to
remove it.
FRONT TURN-SIGNAL LIGHT BULB
REPLACEMENT
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
ZC3052750003
Front turn-signal light
Disconnect the connector, and twist the front turn-signal light
socket to remove it.
LIGHTING
54Ac-169
HEADLIGHT
FRONT SIDE-MARKER LIGHT BULB
REPLACEMENT
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
ZC6015510000
Front side-marker light
Disconnect the connector, and twist the front side-marker light
socket to remove it.
HEADLIGHT AUTOMATIC SHUTDOWN FUNCTION
CHECK
M15410900164USA0000010000
Confirm that the headlights turn OFF in one second if the ignition
key is pulled out and the driver's door is opened when the ignition
switch is ON and the lighting switch is ON (HEAD position). If
there is a malfunction, perform the troubleshooting (Refer to P.
54Ac-25).
CONFIGURATION FUNCTION
M15410900014USA0000010000
With the scan tool MB991958 operation, the following
functions can be programmed. The programmed
information is held even when the battery is
disconnected.
Adjustment
item (scan tool
display)
Adjustment item
Adjustment contents
(scan tool display)
Adjusting contents
Turn
power
source
Adjustment of turn-
signal
light
operation condition
ACC or IG1
Operable with ACC or ON position
IG1
Operable with ON position (default)
Comfort flasher With/without
comfort
flasher
function
Disable
Without function
Enable
With function (default)
Comfort flasher
switch time
Switch
operation
time to activate the
comfort
flasher
function
Normal
0.4 seconds (default)
Long
0.8 seconds
54Ac-170
LIGHTING
HEADLIGHT
Adjustment
item (scan tool
display)
Adjustment item
Adjustment contents
(scan tool display)
Adjusting contents
Hazard answer
back
Adjustment of the
number of keyless
hazard warning light
answer
back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (default)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
Without function
Headlight auto
cut customize
Adjustment
of
headlight automatic
shutdown function
Disable
Without function
C-spec.
With function (default)
REMOVAL AND INSTALLATION
M15410900020USA0000010000
ZC601652
1
3
6
4
5
7
AA00
2
8
1.5 ± 0.3 N·m
14 ± 2 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
Removal Steps
·
Front bumper assembly (Refer to
GROUP 51A - Front Bumper
Assembly P.51A-3.)
Removal Steps
1.
Front bumper bracket
LIGHTING
54Ac-171
HEADLIGHT
Removal Steps
2.
Square nut
<<A>>
3.
Headlight assembly
4.
Headlight bulb socket cover <Vehicles
with discharge headlight>
5.
Connector <Vehicles with discharge
headlight>
Removal Steps
6.
Headlight control unit <Vehicles with
discharge headlight>
<<B>>
7.
Headlight
bulb
<Vehicles
with
discharge headlight>
8.
Grommet
REMOVAL SERVICE POINTS
<<A>> HEADLIGHT ASSEMBLY REMOVAL
When removing the headlight assembly of the right side, remove
the washer fluid inlet.
<<B>> BULB REMOVAL <VEHICLES WITH DISCHARGE
HEADLIGHT>
ZC6016530000
Socket cover
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty,
immediately clean it with alcohol or thinner. After drying
completely, install the bulb.
1.
Twist the socket cover to remove.
ZC601654 0000
Igniter
Spring
2.
Disconnect the igniter.
3.
Release the bulb securing spring, and remove the bulb.
54Ac-172
LIGHTING
HEADLIGHT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст